When installing the name plates or emblem, heat the vehicle body and name plates or emblem using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Name Plate or Emblem | 20 to 30°C (68 to 86°F) |
Do not heat the vehicle body, name plates or emblem excessively.
75431
1.INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new luggage compartment door emblem.
Remove the release paper from the luggage compartment door emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Engage the 2 pins and install the luggage compartment door emblem.
75442
2.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new No. 2 luggage compartment door name plate.
Remove the release paper from the No. 2 luggage compartment door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 2 luggage compartment door name plate as shown in the illustration.
| *a | Release Paper | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 24.4 mm (0.961 in.) | B | 25.0 mm (0.984 in.) |
| C | 47.1 mm (1.85 in.) | - | - |
75443A
3.INSTALL NO. 3 LUGGAGE COMPARTMENT DOOR PLATE
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new No. 3 luggage compartment door plate.
Remove the release paper from the No. 3 luggage compartment door plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 3 luggage compartment door plate as shown in the illustration.
| *a | Release Paper | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 51.2 mm (2.02 in.) | B | 14.1 mm (0.555 in.) |
| C | 19.5 mm (0.768 in.) | D | 54.9 mm (2.16 in.) |
| E | 16.0 mm (0.630 in.) | F | 19.5 mm (0.768 in.) |
| G | 52.9 mm (2.08 in.) | H | 77.9 mm (3.07 in.) |
| I | 48.8 mm (1.92 in.) | J | 53.8 mm (2.12 in.) |
| K | 61.5 mm (2.42 in.) | L | 45.4 mm (1.79 in.) |
75441A
4.INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new No. 1 luggage compartment door name plate.
Remove the release paper from the No. 1 luggage compartment door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 1 luggage compartment door name plate as shown in the illustration.
| *a | Release Paper | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 79.4 mm (3.13 in.) | B | 75.9 mm (2.99 in.) |
| C | 100.9 mm (3.97 in.) | - | - |
75374
5.INSTALL SIDE PANEL EMBLEM (for LH Side)
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new side panel emblem.
Remove the release paper from the side panel emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the side panel emblem as shown in the illustration.
| *a | Release Paper | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 171.8 mm (6.76 in.) | B | 213.2 mm (8.39 in.) |
| C | 39.7 mm (1.56 in.) | - | - |
75374
6.INSTALL SIDE PANEL EMBLEM (for RH Side)
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new side panel emblem.
Remove the release paper from the side panel emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the side panel emblem as shown in the illustration.
| *a | Release Paper | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 48.0 mm (1.89 in.) | B | 210.4 mm (8.28 in.) |
| C | 171.5 mm (6.75 in.) | - | - |