Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2014.05
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0169499 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the navigation receiver assembly via this circuit.

WIRING DIAGRAM

E268438E53
0.865,2.219 1.302,2.438 0.438,0.219 10 false UJSS 5.938,0.646 6.375,0.865 0.438,0.219 10 false US1- 0.833,1.427 1.271,1.646 0.438,0.219 10 false UDO+ 0.865,0.646 1.302,0.865 0.438,0.219 10 false UDO- 1.354,0.542 1.51,0.74 0.156,0.198 10 false 2 1.354,1.323 1.51,1.521 0.156,0.198 10 false 3 5.708,1.323 5.865,1.521 0.156,0.198 10 false 3 5.719,0.531 5.875,0.729 0.156,0.198 10 false 2 1.354,2.104 1.51,2.302 0.156,0.198 10 false 5 5.708,2.104 5.865,2.302 0.156,0.198 10 false 5 5.938,1.438 6.375,1.656 0.438,0.219 10 false US1+ 5.938,2.229 6.375,2.448 0.438,0.219 10 false USG1 0.406,2.833 1.635,3.292 1.229,0.458 10 false No. 1 Stereo Jack Adapter Assembly 3.271,1.771 3.969,2.021 0.698,0.25 10 false (Shielded) 5.667,2.646 6.479,2.854 0.813,0.208 10 false I147 5.656,2.813 6.865,3.292 1.208,0.479 10 false Navigation Receiver Assembly 2.448,3.271 5.031,3.469 2.583,0.198 10 false : Data Signal (USB Communication Line) 0.406,2.677 0.802,2.885 0.396,0.208 10 false I146

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the I147 navigation receiver assembly connector.


b.

Disconnect the I146 No. 1 stereo jack adapter assembly connector.


c.
E289734C04
1.51,0.198 1.958,0.438 0.448,0.24 1.49,2.333 1.938,2.573 0.448,0.24 1.177,1.667 1.625,1.427 false 2.125,1.854 1.771,1.563 false 2.219,1.552 1.792,1.417 false 2.271,3.333 1.781,3.438 false 2.271,3.708 1.771,3.531 false 1.146,3.625 1.635,3.438 false 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 0.115,2.375 0.427,2.531 0.313,0.156 10 false *b 1.594,0.25 2.115,0.458 0.521,0.208 10 false I147 0.813,1.635 1.333,1.844 0.521,0.208 10 false US1+ 2.156,1.844 2.677,2.052 0.521,0.208 10 false USG1 2.25,1.542 2.771,1.75 0.521,0.208 10 false US1- 1.573,2.375 2.094,2.583 0.521,0.208 10 false I146 0.802,3.615 1.323,3.823 0.521,0.208 10 false UDO- 2.323,3.24 2.844,3.448 0.521,0.208 10 false UDO+ 2.302,3.729 2.823,3.938 0.521,0.208 10 false UJSS
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I146-2 (UDO-) - I147-2 (US1-) Always Below 1 Ω
I146-3 (UDO+) - I147-3 (US1+) Always Below 1 Ω
I146-5 (UJSS) - I147-5 (USG1) Always Below 1 Ω
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR