Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › from 2014.05
RM2040EQ _56 Audio / Visual / Telematics _014717 NAVIGATION / MULTI INFO DISPLAY _0169499 NAVIGATION SYSTEM(for SD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the navigation receiver assembly.

WIRING DIAGRAM

E287097E22
0.531,0.781 2.385,0.979 1.854,0.198 10 false from Auxiliary Battery 0.406,1.563 2.25,1.781 1.844,0.219 10 false from ACC NO. 1 Relay 0.469,2.365 2.313,2.625 1.844,0.26 10 false from IG1 NO. 2 Relay 3.406,0.948 4.25,1.177 0.844,0.229 10 false RADIO-B 3.375,1.75 5.208,1.948 1.833,0.198 10 false ECU-ACC 3.229,2.531 4.615,2.813 1.385,0.281 10 false ECU-IG1 NO. 2 5.573,3.594 6.781,4.208 1.208,0.615 10 false Navigation Receiver Assembly 5.469,0.792 5.781,0.99 0.313,0.198 10 false I64 5.469,1.583 5.781,1.781 0.313,0.198 10 false I64 5.469,2.375 5.781,2.573 0.313,0.198 10 false I67 5.469,3.156 5.781,3.354 0.313,0.198 10 false I64 5.521,2.99 5.833,3.188 0.313,0.198 10 false 7 5.51,2.188 5.823,2.385 0.313,0.198 10 false 1 5.51,1.385 5.823,1.583 0.313,0.198 10 false 3 5.51,0.604 5.823,0.802 0.313,0.198 10 false 4 5.802,0.792 6.26,1.021 0.458,0.229 10 false +B1 5.802,1.573 6.26,1.802 0.458,0.229 10 false ACC1 5.813,2.375 6.271,2.604 0.458,0.229 10 false IG 5.813,3.167 6.271,3.396 0.458,0.229 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the I64 and I67 navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I64-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I64-4 (+B1) - I64-7 (GND1) Poewr switch off 11 to 14 V
I64-3 (ACC1) - I64-7 (GND1) Power switch on (ACC) 11 to 14 V
I67-1 (IG) - I64-7 (GND1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR