Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2015.04
RM2040EQ _59 Vehicle Exterior _014735 DOOR / HATCH _0075152 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B280381C15
0.703,0.0010 0.88,0.178 0.177,0.177 10 *1 2.512,0.0010 2.689,0.178 0.177,0.177 10 *2
*1 Centering Bolt
*2 Standard Bolt


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas *a through *r are within each standard range.

B400617N02
1.448,0.927 1.604,1.125 0.156,0.198 10 false a 1.417,1.802 1.573,2 0.156,0.198 10 false b 2.677,1.042 2.833,1.24 0.156,0.198 10 false c 2.635,1.75 2.792,1.948 0.156,0.198 10 false d 4.063,0.885 4.302,1.083 0.24,0.198 10 false e 4.052,1.573 4.292,1.771 0.24,0.198 10 false f 5.958,1.396 6.198,1.594 0.24,0.198 10 false g 5.958,2.104 6.198,2.302 0.24,0.198 10 false h 6.813,3.406 7.052,3.604 0.24,0.198 10 false i 6.615,3.875 6.854,4.073 0.24,0.198 10 false j 6.438,5.375 6.677,5.573 0.24,0.198 10 false k 6.677,4.813 6.917,5.01 0.24,0.198 10 false l 4.115,5.5 4.354,5.698 0.24,0.198 10 false m 2.458,5.667 2.698,5.865 0.24,0.198 10 false n 2.854,5.365 3.094,5.563 0.24,0.198 10 false o 0.781,4.833 1.021,5.031 0.24,0.198 10 false p 1.167,4.583 1.406,4.781 0.24,0.198 10 false q 0.729,3.292 0.969,3.49 0.24,0.198 10 false r

Standard Clearance
Area Measurement Area Measurement
a 3.5 to 6.5 mm (0.138 to 0.256 in.) b 0.5 to 3.5 mm (0.0197 to 0.138 in.)
c 4.1 to 7.1 mm (0.161 to 0.280 in.) d 0.9 to 3.9 mm (0.0354 to 0.154 in.)
e 4.3 to 7.3 mm (0.169 to 0.287 in.) f -1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
g 4.3 to 7.3 mm (0.169 to 0.287 in.) h -1.0 to 2.0 mm (0.0394 to 0.0787 in.)
i -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) j 3.0 to 6.0 mm (0.118 to 0.236 in.)
k 3.0 to 6.0 mm (0.118 to 0.236 in.) l -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
m 3.2 to 7.4 mm (0.126 to 0.291 in.) n 3.3 to 5.7 mm (0.130 to 0.224 in.)
o -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) p 3.3 to 5.7 mm (0.130 to 0.224 in.)
q -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) r 2.3 to 6.3 mm (0.0906 to 0.248 in.)


Hide 2.ADJUST REAR DOOR

NOTICE:

Make sure to turn the power switch off when adjusting door lock strikers.


a.

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  

B334514


b.

Tighten the hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B280549

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)