The thermistor assembly detects the auxiliary battery temperature. The resistance of the thermistor assembly built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the thermistor assembly resistance. Conversely, the higher the temperature, the lower the resistance. The thermistor assembly is connected to the power management control ECU. A voltage of 5 V is supplied to the thermistor assembly from the THB terminal of the power management control ECU through its internal resistor R. This means that resistor R and the thermistor assembly are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the power management control ECU reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.
Characteristics of the thermistor assembly resistance (reference values) are as follows.
| Terminal | THB
(with Connector Disconnected) |
Resistance | Ambient Temperature |
|---|---|---|---|
| THB - E2 | 4.5 to 5.5 V | 3.00 to 3.73 kΩ | Approximately 10°C (50°F) |
| 1.60 to 1.80 kΩ | Approximately 25°C (77°F) | ||
| 0.80 to 1.00 kΩ | Approximately 40°C (104°F) |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0516-769 | Battery Temperature Sensor Circuit Low | Malfunction in the thermistor assembly circuit (short to GND) | ·
Thermistor assembly ·
Wire harness or connector ·
Power management control ECU |
Does not come on | Master Warning Light:
Does not come on |
| P0517-770 | Battery Temperature Sensor Circuit High | Malfunction in the thermistor assembly circuit (open or short to +B) | ·
Thermistor assembly ·
Wire harness or connector ·
Power management control ECU |
Does not come on | Master Warning Light:
Does not come on |
Read the freeze frame data using the intelligent tester. In the freeze frame data, some information is recorded about the vehicle conditions at the moment a malfunction occurred. This information can be helpful when troubleshooting.
After confirming that DTC P0516-769 or P0517-770 is output, use the intelligent tester to check "Auxiliary Batt Temperature" in the Hybrid Control Data List.
| Displayed Temperature | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit or short to +B |
| 215°C (419°F) | Short circuit or short to GND |
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0340-886)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
| Tester Display |
|---|
| Auxiliary Batt Temperature |
Read the Data List.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 215°C (419°F) | B |
| Same as actual temperature | C |
Turn the power switch off.
A
B
C
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
Disconnect connector O26 from the thermistor assembly.
| *a | Front view of wire harness connector
(to Thermistor Assembly) |
Connect terminals 2 (THB) and 1 (E2) of vehicle side connector O26 of the thermistor assembly.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
| Tester Display |
|---|
| Auxiliary Batt Temperature |
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Auxiliary Batt Temperature | Terminals THB and E2 connected.
Power switch on (IG) |
215°C (419°F) |
Turn the power switch off.
Connect the thermistor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector O26 from the thermistor assembly.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
| Tester Display |
|---|
| Auxiliary Batt Temperature |
Read the Data List.
| Tester Display | Switch Condition | Specified Condition |
|---|---|---|
| Auxiliary Batt Temperature | Power switch on (IG) | -40°C (-40°F) |
Turn the power switch off.
Connect the thermistor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Power Management Control ECU) |
Connect terminals 27 (THB) and 26 (ETHB) of connector I3 of the power management control ECU.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.
| Tester Display |
|---|
| Auxiliary Batt Temperature |
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Auxiliary Batt Temperature | Terminals THB and ETHB connected.
Power switch on (IG) |
215°C (419°F) |
Turn the power switch off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connector O26 from the thermistor assembly.
Disconnect connector I3 from the power management control ECU.
| *a | Front view of wire harness connector
(to Thermistor Assembly) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O26-2 (THB) - I3-27 (THB) | Power switch off | Below 1 Ω |
| O26-1 (E2) - I3-26 (ETHB) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O26-2 (THB) or I3-27 (THB)- Body ground and other terminals | Power switch off | 10 kΩ or higher |
| O26-1 (E2) or I3-26 (ETHB)- Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the thermistor assembly connector.
Connect the power management control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG