Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0851-775  Park / Neutral Switch Input Circuit Low  


DESCRIPTION

Refer to the description for DTC P0705-757 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0705-757).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0851-775 Park / Neutral Switch Input Circuit Low N signal line malfunction
·

Wire harness or connector

·

Shift lever position sensor

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0705-757 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0705-757).

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
P0851-775 only is output. A
P0705-757 is also output. B



e.

Turn the power switch off.



A

2.CHECK SHIFT LEVER POSITION SENSOR

B

2.CHECK SHIFT LEVER POSITION SENSOR
a.

Turn the power switch on (IG).


b.
A259789C73
1.208,0.948 1.625,1.188 0.417,0.24 1.521,1.771 1.719,2.365 false 0.198,0.146 0.51,0.375 0.313,0.229 10 false *a 1.302,1 1.677,1.219 0.375,0.219 10 false A39 1.719,2.385 2.01,2.635 0.292,0.25 10 false N
*a Component with harness connected
(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-11 (N) - Body ground Power switch on (IG)
Shift lever in N
11 to 14 V
A39-11 (N) - Body ground Power switch on (IG)
Except shift lever in N
1.2 to 2.8 V



c.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

3.CHECK FOR INTERMITTENT PROBLEMS

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

OK

5.INSPECT SHIFT LEVER POSITION SENSOR

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.INSPECT SHIFT LEVER POSITION SENSOR
a.

Disconnect the shift lever position sensor connector.


b.
A210243C40
0.219,1.167 0.615,1.427 0.396,0.26 1.365,1.833 1.458,1.458 true 1.781,1.823 1.583,1.24 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.76,1.854 2.031,2.115 0.271,0.26 10 false N 1.24,1.854 1.51,2.115 0.271,0.26 10 false +B 0.281,1.208 0.604,1.448 0.323,0.24 10 false E73
*a Component without harness connected
(Shift Lever Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E73-8 (+B) - E73-2 (N) Shift lever in N Below 1 Ω
E73-8 (+B) - E73-2 (N) Except shift lever in N 4.2 to 5.2 kΩ



c.

Connect the shift lever position sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG