Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A0D-350  High Voltage System Inter-Lock Circuit High  P0A0D-351  High Voltage System Inter-Lock Circuit High  


DESCRIPTION

When the power management control ECU detects that a safety device is operated, it will prohibit hybrid system operation or shut off the system main relay. The 5 safety devices are located as follows; 1 in the service plug grip, and at the inverter with converter assembly, there is 1 on the connector cover assembly for the air conditioning fuse, 1 on the upper inverter cover for the terminals of the motor cable, 1 on the upper inverter cover for the terminals of the generator cable and 1 in the No. 4 engine wire (air conditioning harness). If the service plug grip, connector cover assembly, upper inverter cover, or No. 4 engine wire (air conditioning harness) is removed, the interlock signal line will be open. If the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. If the safety devices are re-installed correctly, the system will return to normal when the power switch is turned on (IG).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A0D-350 High Voltage System Inter-Lock Circuit High Operating any of the safety devices with the vehicle stopped (ILK signal is ON) and turning the power switch on (IG)
·

Wire harness or connector

·

Power management control ECU

·

Service plug grip

·

Inverter with converter assembly

·

No. 4 engine wire

·

Upper inverter cover


Does not come on Master Warning Light:
Comes on
P0A0D-351 High Voltage System Inter-Lock Circuit High Interlock signal line opens (ILK signal is ON) while the vehicle is being driven
·

Wire harness or connector

·

Power management control ECU

·

Service plug grip

·

Inverter with converter assembly

·

No. 4 engine wire

·

Upper inverter cover


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A260167E04
3.844,4.146 4.927,4.552 1.083,0.406 10 false Service Plug Grip (Interlock Switch) 3.844,3.979 4.177,4.156 0.333,0.177 10 false r2 4.896,3.594 5.052,3.75 0.156,0.156 10 false 1 3.76,3.594 3.917,3.75 0.156,0.156 10 false 2 0.792,3.469 2.969,3.646 2.177,0.177 10 false Inverter with Converter Assembly 0.792,3.292 1.125,3.469 0.333,0.177 10 false A14 0.844,2.396 2.25,2.865 1.406,0.469 10 false No. 4 Engine Wire (Air Conditioner harness) 0.885,1.458 2.146,1.802 1.26,0.344 10 false Upper Inverter Cover (Motor Cable Side) 5.813,2.844 7.073,3.188 1.26,0.344 10 false Power Management Control ECU 5.813,2.667 6.146,2.844 0.333,0.177 10 false A38 5.083,2.146 5.26,2.302 0.177,0.156 10 false 5 5.073,1.219 5.313,1.375 0.24,0.156 10 false 16 5.719,1.219 5.958,1.375 0.24,0.156 10 false 22 4.677,2.146 5.031,2.302 0.354,0.156 10 false ILKO 4.76,1.208 5.115,1.365 0.354,0.156 10 false ILKI 5.969,1.219 6.323,1.375 0.354,0.156 10 false ILK 6.75,0.479 6.979,0.635 0.229,0.156 10 false +B 4.625,3.594 4.979,3.75 0.354,0.156 10 false ILK 3.906,3.594 4.26,3.75 0.354,0.156 10 false GND 2.865,1.469 4.302,1.833 1.438,0.365 10 false Upper Inverter Cover (Generator Cable Side) 3.021,2.385 4.156,2.719 1.135,0.333 10 false Connector Cover Assembly

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A0D only is output. A
P0A1D is output B



e.

Turn the power switch off.



A

2.CLEAR DTC

B

2.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 236

f.

Turn the power switch off.

Result:
Proceed to
NEXT




NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0A0D-350 or P0A0D-351 is output again. A
Neither P0A0D-350 or P0A0D-351 is output again. B



e.

Turn the power switch off.



A

4.CHECK SERVICE PLUG GRIP

B

12.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
4.CHECK SERVICE PLUG GRIP
CAUTION:

Be sure to wear insulated gloves.


a.

Check if the service plug grip is installed correctly.

Result:
Proceed to
OK
NG


HINT:
·

For the removal and installation procedures (Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>COMPONENTS).

·

P0A0D-350 is also set if the power switch is turned on (IG) with the service plug grip removed. Confirm the conditions when the malfunction occurred.





OK

5.CHECK UPPER INVERTER COVER (GENERATOR CABLE SIDE)

NG

INSTALL PARTS CORRECTLY

5.CHECK UPPER INVERTER COVER (GENERATOR CABLE SIDE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258951

Check if the upper inverter cover (generator cable side) of the inverter with converter assembly is installed correctly.

OK:

The upper inverter cover (generator cable side) is installed correctly.


Result:
Proceed to
OK
NG




OK

6.CHECK UPPER INVERTER COVER (MOTOR CABLE SIDE)

NG

INSTALL PARTS CORRECTLY

6.CHECK UPPER INVERTER COVER (MOTOR CABLE SIDE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258952

Check if the upper inverter cover (motor cable side) of the inverter with converter assembly is installed correctly.

OK:

The upper inverter cover (motor cable side) is installed correctly.


Result:
Proceed to
OK
NG




OK

7.CHECK CONNECTOR COVER ASSEMBLY

NG

INSTALL PARTS CORRECTLY

7.CHECK CONNECTOR COVER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Check if the connector cover assembly of the inverter with converter assembly is installed correctly.

OK:

The connector cover assembly is installed correctly.


Result:
Proceed to
OK
NG




OK

8.CHECK NO. 4 ENGINE WIRE

NG

INSTALL PARTS CORRECTLY

8.CHECK NO. 4 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259713

Check if the No. 4 engine wire (air conditioning harness) is connected correctly.

OK:

The No. 4 engine wire (air conditioning harness) connector is connected correctly.



Result:
Proceed to
OK
NG



OK

9.CHECK POWER MANAGEMENT CONTROL ECU

NG

INSTALL PARTS CORRECTLY

9.CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A258451C46
0.198,1.063 0.656,1.344 0.458,0.281 2.125,1.865 1.573,1.073 false 0.292,1.125 0.656,1.344 0.365,0.219 10 false A14 2.021,1.875 2.313,2.042 0.292,0.167 10 false ILKI 0.125,0.104 0.302,0.271 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A14-16 (ILKI) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

10.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERLOCK)

NG

13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
10.CHECK INVERTER WITH CONVERTER ASSEMBLY (INTERLOCK)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.
A258450C08
1.167,1.677 1.583,1.917 0.417,0.24 1.479,0.896 1.885,0.323 false 1.479,1 1.906,1.771 false 0.135,0.083 0.417,0.25 0.281,0.167 10 false *a 1.25,1.729 1.521,1.896 0.271,0.167 10 false A14 1.927,0.229 2.292,0.406 0.365,0.177 10 false ILKO 1.938,1.708 2.302,1.885 0.365,0.177 10 false ILKI
*a Component without harness connected
(Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A14-16 (ILKI) - A14-5 (ILKO) Power switch off Less than 10 Ω


NOTICE:

Do not remove the upper inverter cover, connector cover assembly and No. 4 engine wire.



d.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - BODY GROUND)

NG

14.CHECK UPPER INVERTER COVER (GENERATOR CABLE SIDE)
11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.

Install the service plug grip.


d.
A258451C47
0.198,1.01 0.656,1.292 0.458,0.281 1.958,0.417 1.583,0.99 false 0.302,1.073 0.708,1.333 0.406,0.26 10 false A14 2,0.323 2.365,0.49 0.365,0.167 10 false ILKO 0.125,0.052 0.302,0.219 0.177,0.167 10 false *a
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A14-5 (ILKO) - Body ground Power switch off Below 1 Ω



e.

Remove the service plug grip.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

12.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)

NG

18.CHECK SERVICE PLUG GRIP
12.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
a.

Check the connections of each connector.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.

Disconnect connector A38 from the power management control ECU.


d.
A284484C04
0.26,0.979 0.625,1.24 0.365,0.26 1.167,3.531 1.531,3.792 0.365,0.26 2.146,1.823 1.563,0.927 false 1.208,4.167 0.823,3.729 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.073,2.01 0.385,2.167 0.313,0.156 10 false *b 2.219,1.76 2.625,1.948 0.406,0.188 10 false ILKI 1.26,4.115 1.667,4.302 0.406,0.188 10 false ILK 0.323,1.031 0.781,1.229 0.458,0.198 10 false A14 1.229,3.594 1.688,3.792 0.458,0.198 10 false A38
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A14-16 (ILKI) - A38-22 (ILK) Power switch off Below 1 Ω



e.

Connect the power management control ECU connector.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK UPPER INVERTER COVER (GENERATOR CABLE SIDE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258951

Remove the upper inverter cover (generator cable side) from the inverter with converter assembly.


c.
A259719C02
0.052,0.021 0.26,0.177 0.208,0.156 10 false *1
*1 Upper Inverter Cover (Generator Cable Side)


Check the condition of the upper inverter cover (generator cable side) interlock.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.



d.

Install the upper inverter cover (generator cable side) to the inverter with converter assembly.

Result:
Proceed to
OK
NG




OK

15.CHECK UPPER INVERTER COVER (MOTOR CABLE SIDE)

NG

REPLACE UPPER INVERTER COVER (GENERATOR CABLE SIDE)

15.CHECK UPPER INVERTER COVER (MOTOR CABLE SIDE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258952

Remove the upper inverter cover (motor cable side) from the inverter with converter assembly.


c.
A259719C02
0.052,0.021 0.26,0.177 0.208,0.156 10 false *1
*1 Upper Inverter Cover (Motor Cable Side)


Check the condition of the upper inverter cover (motor cable side) interlock.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.



d.

Install the upper inverter cover (motor cable side) to the inverter with converter assembly.

Result:
Proceed to
OK
NG




OK

16.CHECK CONNECTOR COVER ASSEMBLY

NG

REPLACE UPPER INVERTER COVER (MOTOR CABLE SIDE)

16.CHECK CONNECTOR COVER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.


c.
A284858C02
0.063,0.063 0.375,0.219 0.313,0.156 10 *1
*1 Connector Cover Assembly


Check the condition of the connector cover assembly interlock.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.


HINT:

The connector cover assembly is not available separately. If it requires replacement, replace the inverter with converter assembly.



d.

Install the connector cover assembly to the inverter with converter assembly.

Result:
Proceed to
OK
NG




OK

17.CHECK NO. 4 ENGINE WIRE (NO. 4 ENGINE WIRE CONNECTOR)

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

17.CHECK NO. 4 ENGINE WIRE (NO. 4 ENGINE WIRE CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259713

Disconnect the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.


c.
A260208C04
0.054,0.0 0.251,0.184 0.197,0.184 10 *1
*1 No. 4 engine wire (air conditioning harness)


Check the No. 4 engine wire (air conditioning harness) interlock.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.



d.

Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.


Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

REPLACE NO. 4 ENGINE WIRE

18.CHECK SERVICE PLUG GRIP
a.

Remove the service plug grip.


b.
A206690C05
0.185,0.121 0.342,0.278 0.157,0.157 10 *1
*1 Service Plug Grip


Check the condition of the service plug grip interlock.

OK:

Dirt or foreign objects have not entered the connection, and there is no evidence of contamination.



c.

Install the service plug grip.

Result:
Proceed to
OK
NG




OK

19.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)

NG

19.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259721C02
1.219,0.229 1.427,0.406 0.208,0.177 10 true *1
*1 Interlock Connector


Check that the interlock connector at the service plug grip installation socket is connected correctly.

OK:

The connector is connected correctly.


Result:
Proceed to
OK
NG




OK

20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - SERVICE PLUG GRIP)

NG

CONNECT SECURELY

20.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - SERVICE PLUG GRIP)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.

Disconnect connector r2 from the service plug grip.


d.
A284483C02
0.219,0.74 0.563,0.99 0.344,0.25 1.313,3.885 1.656,4.135 0.344,0.25 1.552,0.677 2.542,0.177 false 1.792,4.479 2.125,4.104 false 0.073,0.052 0.385,0.208 0.313,0.156 10 *a 0.083,1.74 0.396,1.896 0.313,0.156 10 *b 2.594,0.104 3.208,0.302 0.615,0.198 10 ILKO 0.271,0.792 0.625,0.99 0.354,0.198 10 A14 1.417,3.938 1.771,4.135 0.354,0.198 10 r2 1.573,4.417 2.188,4.615 0.615,0.198 10 ILK
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Service Plug Grip)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A14-5 (ILKO) - r2-1(ILK) Power switch off Below 1 Ω



e.

Connect the service plug grip connector.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SERVICE PLUG GRIP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - SERVICE PLUG GRIP)