Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2C-247  Drive Motor "A" Temperature Sensor Circuit Low  P0A2D-249  Drive Motor "A" Temperature Sensor Circuit High  


DESCRIPTION

Refer to the description for DTC P0A2B-250 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A2C-247 Drive Motor "A" Temperature Sensor Circuit Low Short or short to GND in the motor temperature sensor circuit
·

Wire harness or connector

·

Power management control ECU

·

Hybrid vehicle transaxle assembly (Motor temperature sensor)


Does not come on Master Warning Light:
Comes on
P0A2D-249 Drive Motor "A" Temperature Sensor Circuit High Open or short to +B in the motor temperature sensor circuit
·

Wire harness or connector

·

Power management control ECU

·

Hybrid vehicle transaxle assembly (Motor temperature sensor)


Does not come on Master Warning Light:
Comes on

HINT:

After confirming that DTC P0A2C-247 or P0A2D-249 is output, use the intelligent tester to check "Motor Temp No1" in the power management control ECU Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND


WIRING DIAGRAM

A159825E76
5.042,2.677 5.385,2.865 0.344,0.188 10 false A39 0.427,2.531 0.771,2.719 0.344,0.188 10 false E15 1.771,1.906 2.208,2.094 0.438,0.188 10 false MMTG 1.865,1.167 2.208,1.354 0.344,0.188 10 false MMT 5.146,1.167 5.49,1.354 0.344,0.188 10 false MMT 5.146,1.906 5.635,2.094 0.49,0.188 10 false MMTG 2.292,1.906 2.5,2.094 0.208,0.188 10 false 3 2.281,1.167 2.458,1.354 0.177,0.188 10 false 1 4.885,1.167 5.229,1.354 0.344,0.188 10 false 35 4.885,1.906 5.229,2.094 0.344,0.188 10 false 34 5.042,2.833 6.313,3.302 1.271,0.469 10 false Power Management Control ECU 0.417,2.698 2.646,3.146 2.229,0.448 10 false Hybrid Vehicle Transaxle Assembly (Motor Temperature Sensor)

PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.READ VALUE USING INTELLIGENT TESTER (MOTOR TEMP NO1)

NG

CONNECT SECURELY

2.READ VALUE USING INTELLIGENT TESTER (MOTOR TEMP NO1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temp No1
50003 236 570

d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)

B

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)

C

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)
a.
A259191

Disconnect the motor temperature sensor connector.


b.
A259194C03
0.34,1.031 0.803,1.317 0.463,0.286 0.414,1.085 0.7,1.248 0.286,0.163 10 E15 0.918,1.723 1.26,1.887 0.341,0.163 10 MMT 2.121,1.723 2.565,1.887 0.443,0.163 10 MMTG 0.122,0.079 0.304,0.242 0.182,0.163 10 *a 1.142,1.701 1.44,1.254 false 2.35,1.701 2.053,1.254 false
*a Front view of wire harness connector
(to Motor Temperature Sensor)


Connect terminals 1 (MMT) and 3 (MMTG) of vehicle side connector E15 of the motor temperature sensor.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temp No1
50003 236 570

e.

Connect the intelligent tester to the DLC3.


f.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No1 Terminals MMT and MMTG connected.
Power switch on (IG)
215°C (419°F)


HINT:

The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



g.

Turn the power switch off.


h.

Connect the motor temperature sensor connector.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - MOTOR TEMPERATURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - MOTOR TEMPERATURE SENSOR)
a.
A249277C37
1.24,1.01 1.604,1.25 0.365,0.24 1.156,1.906 0.979,2.427 false 1.208,1.906 1.417,2.417 false 1.323,1.073 1.708,1.24 0.385,0.167 10 false A39 0.135,0.208 0.406,0.375 0.271,0.167 10 false *a 0.823,2.469 1.323,2.635 0.5,0.167 10 false MMT 1.271,2.458 1.771,2.625 0.5,0.167 10 false MMTG
*a Component with harness connected
(Power Management Control ECU)


Connect terminals 35 (MMT) and 34 (MMTG) of connector A39 of the power management control ECU.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.


e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No1 Terminals MMT and MMTG connected.
Power switch on (IG)
215°C (419°F)



f.

Turn the power switch off.


g.

Connect the motor temperature sensor connector.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)
a.
A259191

Disconnect the motor temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.

Powertrain > Hybrid Control > Data List
Tester Display
Motor Temp No1
50003 236 570

e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Motor Temp No1 Power switch on (IG) -40°C (-40°F)


HINT:

The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



f.

Turn the power switch off.


g.

Connect the motor temperature sensor connector.

Result:
Proceed to
OK
NG




OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - POWER MANAGEMENT CONTROL ECU)
6.CHECK HARNESS AND CONNECTOR (MOTOR TEMPERATURE SENSOR - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the motor temperature sensor connector.


b.

Disconnect connector A39 from the power management control ECU.


c.

Measure the resistance according to the value(s) in the table below.

A335052C02
0.521,1.177 0.927,1.427 0.406,0.25 5.354,1.688 5.76,1.938 0.406,0.25 1.042,1.938 1.323,1.396 true 2.063,1.938 1.823,1.417 true 4.479,2.458 4.76,1.917 true 5.052,2.448 4.813,1.927 true 0.625,0.573 0.938,0.771 0.313,0.198 10 false *a 3.531,0.25 3.844,0.448 0.313,0.198 10 false *b 0.615,1.25 0.927,1.448 0.313,0.198 10 false E15 5.458,1.76 5.771,1.958 0.313,0.198 10 false A39 0.885,1.969 1.313,2.208 0.427,0.24 10 false MMT 1.896,1.979 2.49,2.229 0.594,0.25 10 false MMTG 4.302,2.469 4.729,2.708 0.427,0.24 10 false MMT 4.927,2.479 5.469,2.708 0.542,0.229 10 false MMTG
*a Front view of wire harness connector
(to Motor Temperature Sensor)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E15-1 (MMT) - A39-35 (MMT) Power switch off Below 1 Ω
E15-3 (MMTG) - A39-34 (MMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
E15-1 (MMT) or A39-35 (MMT) - Body ground and other terminals Power switch off 10 kΩ or higher
E15-3 (MMTG) or A39-34 (MMTG) - Body ground and other terminals Power switch off 10 kΩ or higher



d.

Connect the power management control ECU connector.


e.

Connect the motor temperature sensor connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR