Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3110-223  HV Main Relay  


DESCRIPTION

The power management control ECU monitors the IGCT relay and detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3110-223 HV Main Relay There is a short to +B in the IGCT relay or the IGCT relay is stuck closed.
·

Wire harness or connector

·

IGCT relay

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A264606E05
5.156,2.885 6.469,3.438 1.313,0.552 10 false Power Management Control ECU 5.375,0.396 5.688,0.563 0.313,0.167 10 false +B1 5.375,0.813 5.688,0.979 0.313,0.167 10 false +B2 5.375,1.24 5.792,1.406 0.417,0.167 10 false MREL 5.021,0.479 5.292,0.646 0.271,0.167 10 false A39 5.125,0.25 5.292,0.5 0.167,0.25 10 false 3 5.115,0.688 5.292,0.927 0.177,0.24 10 false 1 5.115,1.135 5.281,1.365 0.167,0.229 10 false 4 5.031,0.906 5.302,1.073 0.271,0.167 10 false A38 5.021,1.344 5.292,1.51 0.271,0.167 10 false A38 3.646,1.063 4.313,1.229 0.667,0.167 10 false PM IGCT 2.927,1.76 3.51,1.927 0.583,0.167 10 false IGCT 3.469,0.781 3.615,0.99 0.146,0.208 10 false 5 3.458,1.219 3.646,1.479 0.188,0.26 10 false 1 2.583,1.198 2.802,1.385 0.219,0.188 10 false 2 2.583,0.781 2.771,0.958 0.188,0.177 10 false 3 0.667,2.563 1.792,2.844 1.125,0.281 10 false Auxiliary Battery 1.156,1.052 1.99,1.271 0.833,0.219 10 false IGCT-MAIN 0.573,1.99 1.208,2.24 0.635,0.25 10 false MAIN 0.531,1.354 1.469,1.635 0.938,0.281 10 false R/B NO.2

CAUTION / NOTICE / HINT

HINT:

If the auxiliary battery voltage is applied to terminal +B1 or +B2 of the power management control ECU, even though the power switch is off, the circuit is shorted to +B.


PROCEDURE

1.INSPECT RELAY (IGCT)
a.

Remove the IGCT relay from the No. 2 engine room relay block.


b.
A253297C09
0.165,0.068 0.398,0.266 0.233,0.198 10 *1
*1 IGCT Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher



c.

Install the IGCT relay.

Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO.2 ENGINE ROOM RELAY BLOCK)

NG

REPLACE RELAY (IGCT)

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO.2 ENGINE ROOM RELAY BLOCK)
a.

Remove the IGCT relay from the No. 2 engine room relay block.


b.

Disconnect connector A38 and A39 from the power management control ECU.


c.

Measure the voltage according to the value(s) in the table below.

A259914C11
1.281,2.354 1.615,2.552 0.333,0.198 1.833,2.354 2.167,2.552 0.333,0.198 1.573,1.729 1.677,2.146 false 2,1.729 2.385,2.125 false 0.844,0.146 1.198,0.365 0.354,0.219 10 false *a 3.948,0.146 4.302,0.365 0.354,0.219 10 false *1 5.854,1.667 6.083,1.885 0.229,0.219 10 false *2 2.313,2.156 2.667,2.365 0.354,0.208 10 false +B1 1.573,2.167 1.917,2.344 0.344,0.177 10 false +B2 1.344,2.385 1.656,2.573 0.313,0.188 10 false A38 1.896,2.385 2.219,2.604 0.323,0.219 10 false A39
*1 No. 2 Engine Room Relay Block *2 IGCT relay
*a Rear view of wire harness connector
(to Power Management Control ECU)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-3 (+B1), A38-1 (+B2) or 5 (IGCT relay) - Body ground Power switch on (IG) Below 1 V



d.

Install the IGCT relay.


e.

Connect the power management control ECU connector.

Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR