Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P321E-318  All HV Gate Blocking Range/Performance  


DESCRIPTION

The power management control ECU sends a block signal to the motor generator control ECU (MG ECU) to shutdown the power supply to the motor. When the system is not in the on (READY) state, it sends an HSDN (MG shutdown signal) signal from the power management control ECU to the motor generator control ECU (MG ECU) to check the function of the HV gate block. When a malfunction is detected in the HV gate block function, DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P321E-318 All HV Gate Blocking Range/Performance
·

An open or ground short in the HV gate block signal circuit when the gate is operating

·

When the HV gate block function is being checked, inverter voltage (VH) drops or current flows in the inverter. (Both the motor (MG2) and the generator (MG1) are malfunctioning.)


·

Wire harness or connector

·

Power management control ECU

·

Inverter with converter assembly


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A259389E04
2.167,0.417 2.427,0.583 0.26,0.167 10 false +B 2.104,0.76 2.427,0.927 0.323,0.167 10 false +B2 1.958,1.104 2.406,1.271 0.448,0.167 10 false HSDN 1.958,1.479 2.406,1.646 0.448,0.167 10 false GND1 1.958,1.823 2.406,1.99 0.448,0.167 10 false GND2 2.406,0.365 2.667,0.531 0.26,0.167 10 false 30 2.406,0.708 2.667,0.875 0.26,0.167 10 false 31 2.406,1.104 2.667,1.271 0.26,0.167 10 false 40 2.406,1.406 2.667,1.573 0.26,0.167 10 false 10 2.406,1.75 2.667,1.917 0.26,0.167 10 false 11 4.563,1.104 4.823,1.271 0.26,0.167 10 false 30 4.802,1.052 5.25,1.219 0.448,0.167 10 false HSDN 0.448,2.333 2.552,2.542 2.104,0.208 10 false Inverter with Converter Assembly 5.979,0.417 6.24,0.583 0.26,0.167 10 false +B 0.458,2.188 0.75,2.354 0.292,0.167 10 false A14 4.51,2.354 6.615,2.563 2.104,0.208 10 false Power Management Control ECU 4.51,2.198 4.802,2.365 0.292,0.167 10 false A38 3.344,0.448 4.208,0.656 0.865,0.208 10 false to INV Fuse

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


c.

Disconnect connector A38 from the power management control ECU.


d.
A335141C02
0.25,1.052 0.667,1.281 0.417,0.229 0.188,3.833 0.604,4.063 0.417,0.229 1.979,1.865 1.906,1.281 true 1.219,4.375 1.031,4.042 true 0.354,0.302 0.667,0.5 0.313,0.198 10 false *a 0.229,2.26 0.542,2.458 0.313,0.198 10 false *b 0.333,1.104 0.646,1.302 0.313,0.198 10 false A14 0.292,3.885 0.604,4.083 0.313,0.198 10 false A38 1.833,1.896 2.271,2.063 0.438,0.167 10 false HSDN 1.094,4.406 1.531,4.573 0.438,0.167 10 false HSDN
*a Front view of wire harness connector
(to Inverter With Converter Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-30 (HSDN) or A14 -40 (HSDN) - Body ground and other terminals Power switch off 10 kΩ or higher
A38-30 (HSDN) - A14-40 (HSDN) Power switch off Below 1 Ω



e.

Connect the power management control ECU connector.


f.

Connect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A14 from the inverter with converter assembly.


A258450C10
1.333,1.667 1.75,1.906 0.417,0.24 1.021,0.958 1.5,0.25 1.5,0.25 1.583,0.25 false 0.781,1.792 1.156,1.198 false 0.135,0.104 0.417,0.271 0.281,0.167 10 false *a 1.396,1.708 1.667,1.875 0.271,0.167 10 false A14 1.635,0.177 2.063,0.354 0.427,0.177 10 false GND1 0.563,1.844 0.99,2.021 0.427,0.177 10 false HSDN
*a Component without harness connected
(Inverter with Converter Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A14-40 (HSDN) - A14-10 (GND1) Power switch off 2.65 to 3.55 kΩ



d.

Connect the inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

NG