Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014718 PARK ASSIST / MONITORING _0075026 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the blind spot monitor sensor.

WIRING DIAGRAM

E224413E21
3.615,0.719 3.927,0.896 0.313,0.177 10 false BLB 3.458,0.604 3.573,0.781 0.115,0.177 10 false 5 3.625,3.302 3.938,3.479 0.313,0.177 10 false BRB 3.458,3.198 3.573,3.375 0.115,0.177 10 false 5 3.625,4.073 4.063,4.25 0.438,0.177 10 false BRGD 3.385,3.979 3.563,4.156 0.177,0.177 10 false 10 3.385,1.396 3.563,1.573 0.177,0.177 10 false 10 3.615,1.51 4.042,1.667 0.427,0.156 10 false BLGD 1.594,0.865 2.583,1.031 0.99,0.167 10 false ECU-IG1 NO. 3 0.188,0.698 1.167,1.021 0.979,0.323 10 false from IG1 NO. 3 Relay 6.146,1.344 7.146,1.896 1,0.552 10 false to CAN Communication System 3.417,2.052 3.781,2.208 0.365,0.156 10 false T21 3.417,2.219 5.031,2.563 1.615,0.344 10 false Blind Spot Monitor Sensor LH 3.469,4.802 5.083,5.146 1.615,0.344 10 false Blind Spot Monitor Sensor RH 0.875,5.302 2.688,5.49 1.813,0.188 10 false : CAN Communication Line 3.469,4.635 3.875,4.792 0.406,0.156 10 false O47

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BATTERY)
a.

Disconnect the O47 blind spot monitor sensor RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O47-5 (BRB) - Body ground Power switch on (IG) 11 to 14 V
O47-5 (BRB) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BODY GROUND)
a.

Disconnect the O47 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O47-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY)
a.

Disconnect the T21 blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
T21-5 (BLB) - Body ground Power switch on (IG) 11 to 14 V
T21-5 (BLB) - Body ground Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BODY GROUND)
a.

Disconnect the T21 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T21-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR