Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014716 AUDIO / VIDEO _0076806 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E277817E55
0.188,3.552 1.344,3.948 1.156,0.396 10 false No. 1 Stereo Jack Adapter Assembly 0.188,3.375 0.521,3.552 0.333,0.177 10 false I146 0.979,0.615 1.583,0.833 0.604,0.219 10 false UPI 0.865,1.188 1.469,1.406 0.604,0.219 10 false UDO- 0.833,1.792 1.438,2.01 0.604,0.219 10 false UDO+ 0.854,2.438 1.458,2.656 0.604,0.219 10 false UJSG 0.865,3.042 1.469,3.26 0.604,0.219 10 false UJSS 1.333,2.927 1.531,3.135 0.198,0.208 10 false 5 1.333,2.313 1.531,2.521 0.198,0.208 10 false 4 1.333,1.646 1.531,1.854 0.198,0.208 10 false 3 1.333,1.042 1.531,1.25 0.198,0.208 10 false 2 1.333,0.479 1.531,0.688 0.198,0.208 10 false 1 3.302,2.833 4.833,3.031 1.531,0.198 10 false (Shielded) 5.958,0.615 6.563,0.833 0.604,0.219 10 false USV1 5.958,1.198 6.563,1.417 0.604,0.219 10 false US1- 5.958,1.813 6.563,2.031 0.604,0.219 10 false US1+ 5.958,2.448 6.563,2.667 0.604,0.219 10 false UGD1 5.958,3.052 6.563,3.271 0.604,0.219 10 false USG1 5.74,2.927 5.938,3.135 0.198,0.208 10 false 5 5.74,2.313 5.938,2.521 0.198,0.208 10 false 4 5.74,1.646 5.938,1.854 0.198,0.208 10 false 3 5.74,1.031 5.938,1.24 0.198,0.208 10 false 2 5.74,0.479 5.938,0.688 0.198,0.208 10 false 1 5.427,3.531 7.135,4 1.708,0.469 10 false Radio and Display Receiver Assembly 5.427,3.365 5.76,3.542 0.333,0.177 10 false I156 1.854,4.177 4.573,4.438 2.719,0.26 10 false : Data Signal (USB Communication Line)

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin playback.

·

When using a USB device, files that are protected by copyright cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B




A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION IS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST)

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the I156 radio and display receiver assembly connector.


b.

Disconnect the I146 No. 1 stereo jack adapter assembly connector.


c.
E289734C07
1.479,0.115 1.906,0.333 0.427,0.219 1.51,2.323 1.938,2.542 0.427,0.219 1.01,0.906 1.583,1.26 false 0.938,1.792 1.594,1.438 false 1.833,1.271 2.396,1 false 1.833,1.427 2.385,1.729 false 1.781,1.552 2.104,1.938 false 1.135,3.198 1.51,3.427 false 1.104,3.688 1.635,3.448 false 1.792,3.427 2.375,3.021 false 1.917,3.438 2.292,3.531 false 1.771,3.542 2.302,3.854 false 0.625,0.729 1.24,0.927 0.615,0.198 10 false UGD1 0.135,0.125 0.75,0.323 0.615,0.198 10 false *a 1.573,0.146 2.188,0.344 0.615,0.198 10 false I156 0.583,1.771 1.198,1.969 0.615,0.198 10 false US1+ 2.115,1.948 2.729,2.146 0.615,0.198 10 false USG1 2.438,1.688 3.052,1.885 0.615,0.198 10 false US1- 2.438,0.875 3.052,1.073 0.615,0.198 10 false USV1 1.604,2.354 2.219,2.552 0.615,0.198 10 false I146 0.156,2.354 0.771,2.552 0.615,0.198 10 false *b 0.885,3.021 1.5,3.219 0.615,0.198 10 false UPI 0.74,3.667 1.354,3.865 0.615,0.198 10 false UDO- 2.406,2.875 3.021,3.073 0.615,0.198 10 false UDO+ 2.333,3.521 2.948,3.719 0.615,0.198 10 false UJSG 2.323,3.865 2.938,4.063 0.615,0.198 10 false UJSS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I156-1 (USV1) Always Below 1 Ω
I146-2 (UDO-) - I156-2 (US1-) Always Below 1 Ω
I146-3 (UDO+) - I156-3 (US1+) Always Below 1 Ω
I146-4 (UJSG) - I156-4 (UGD1) Always Below 1 Ω
I146-5 (UJSS) - I156-5 (USG1) Always Below 1 Ω
I146-1 (UPI) - Body ground Always 10 kΩ or higher
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-4 (UJSG) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Disconnect the I146 No. 1 stereo jack adapter assembly connector.


b.
E226479C44
1.5,0.906 1.979,1.156 0.479,0.25 1.938,2.083 2.531,2.302 false 1.49,2.083 0.844,2.302 false 1.615,0.948 1.99,1.25 0.375,0.302 10 false I146 2.552,2.281 2.979,2.427 0.427,0.146 10 false UJSG 0.563,2.26 0.927,2.458 0.365,0.198 10 false UPI 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I146-4 (UJSG) Power switch on (ACC) 5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the power switch off.

HINT:

When this malfunction occurs, it is necessary to turn the power switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the power switch on (ACC).


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE