Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014716 AUDIO / VIDEO _0076806 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals sent from the combination meter assembly.


for "Bluetooth":

Vehicle speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio and display receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E237358E05
0.385,1.646 3.219,2.042 2.833,0.396 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 0.99,0.813 1.281,0.958 0.292,0.146 10 false SP1 0.052,1.646 0.375,1.823 0.323,0.177 10 false A28 0.698,6.167 2.427,6.573 1.729,0.406 10 false Stereo Component Amplifier Assembly*2 0.417,6.167 0.74,6.344 0.323,0.177 10 false I69 1.365,0.813 1.552,0.958 0.188,0.146 10 false 11 0.458,3.177 2.594,3.458 2.135,0.281 10 false Power Management Control ECU 0.458,3.021 0.75,3.188 0.292,0.167 10 false I3 1.625,2.719 2.021,2.875 0.396,0.156 10 false SPDI 2.094,2.719 2.427,2.948 0.333,0.229 10 false 16 2.938,2.719 3.115,2.875 0.177,0.156 10 false 15 3.948,2.719 4.125,2.875 0.177,0.156 10 false 18 3.948,4.24 4.125,4.396 0.177,0.156 10 false 17 2.927,4.25 3.104,4.406 0.177,0.156 10 false 20 5.385,0.813 5.688,0.958 0.302,0.146 10 false 4 5.385,2.719 5.656,2.865 0.271,0.146 10 false 3 5.604,0.896 5.802,1.042 0.198,0.146 10 false SI 5.594,2.833 5.792,2.979 0.198,0.146 10 false +S 4.99,3.219 5.281,3.479 0.292,0.26 10 false I18 5.26,3.219 7.125,3.479 1.865,0.26 10 false Combination Meter Assembly 5.573,4.24 5.896,4.385 0.323,0.146 10 false SPD 5.313,4.24 5.625,4.406 0.313,0.167 10 false 17 5.573,5.74 5.896,5.885 0.323,0.146 10 false SPD 5.302,5.74 5.49,5.906 0.188,0.167 10 false 17 4.792,6.177 5.26,6.344 0.469,0.167 10 false I67 5.031,6.167 7.115,6.354 2.083,0.188 10 false Navigation Receiver Assembly*2 2.906,5.719 3.083,5.875 0.177,0.156 10 false 19 1.708,5.729 2.031,5.875 0.323,0.146 10 false SPD 2.083,5.719 2.26,5.885 0.177,0.167 10 false 11 4.26,4.677 4.563,4.833 0.302,0.156 10 false I155 4.604,4.677 7.115,4.865 2.51,0.188 10 false Radio and Display Receiver Assembly*1 3.115,6.177 4.365,6.396 1.25,0.219 10 false Junction Connector 2.781,6.177 3.177,6.344 0.396,0.167 10 false I181 2.094,4.25 2.406,4.417 0.313,0.167 10 false 24 0.427,4.688 2.76,4.927 2.333,0.24 10 false Windshield Wiper Relay Assembly*3 0.552,7.135 2.656,7.5 2.104,0.365 10 false *1: for Radio and Display Type 2.802,7.135 4.844,7.438 2.042,0.302 10 false *2: for Navigation Receiver Type 1.719,4.333 2.042,4.479 0.323,0.146 10 false SPD 0.167,4.688 0.448,4.844 0.281,0.156 10 false I72 5.125,7.135 6.792,7.438 1.667,0.302 10 false *3: w/ Auto Wiper System


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

While driving the vehicle, compare the value displayed for "SPEED" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E286967C29
1.5,0.333 1.917,0.583 0.417,0.25 2.135,1.354 2.667,0.667 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.594,0.375 2.052,0.573 0.458,0.198 10 false I18 2.667,0.5 3.125,0.698 0.458,0.198 10 false +S 1.115,3.844 1.427,4.042 0.313,0.198 10 false A 2.781,3.594 3.24,3.792 0.458,0.198 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-3 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I18-3 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265791C24
1.646,0.271 2.063,0.531 0.417,0.26 2.604,1.844 2.406,1.406 false 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.698,0.323 2.323,0.688 0.625,0.365 10 false I155 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.781,1.729 5.094,1.927 0.313,0.198 10 false A 6.167,1.469 6.594,1.688 0.427,0.219 10 false GND
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -


i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I155-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal I155-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I155 radio and display receiver assembly connector.


b.

Disconnect the I181 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I155-17 (SPD) - I181-17 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I18 combination meter assembly connector.


b.

Disconnect the I181 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (+S) - I181-18 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)