Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014716 AUDIO / VIDEO _0076806 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E268438E69
0.896,2.208 1.333,2.427 0.438,0.219 10 false UJSS 5.938,0.667 6.375,0.885 0.438,0.219 10 false US1- 0.865,1.448 1.302,1.667 0.438,0.219 10 false UDO+ 0.896,0.667 1.333,0.885 0.438,0.219 10 false UDO- 1.375,0.521 1.531,0.719 0.156,0.198 10 false 2 1.354,1.323 1.51,1.521 0.156,0.198 10 false 3 5.708,1.323 5.865,1.521 0.156,0.198 10 false 3 5.719,0.531 5.875,0.729 0.156,0.198 10 false 2 1.354,2.104 1.51,2.302 0.156,0.198 10 false 5 5.708,2.104 5.865,2.302 0.156,0.198 10 false 5 5.938,1.458 6.375,1.677 0.438,0.219 10 false US1+ 5.938,2.229 6.375,2.448 0.438,0.219 10 false USG1 0.448,2.688 0.854,2.896 0.406,0.208 10 false I146 0.448,2.865 1.677,3.323 1.229,0.458 10 false No. 1 Stereo Jack Adapter Assembly 3.271,1.771 3.969,2.021 0.698,0.25 10 false (Shielded) 5.781,2.667 6.219,2.885 0.438,0.219 10 false I156 5.781,2.844 7,3.24 1.219,0.396 10 false Radio and Display Receiver Assembly 2.458,3.271 5.021,3.5 2.563,0.229 10 false : Data Signal (USB Communication Line)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the I156 radio and display receiver assembly connector.


b.

Disconnect the I146 No. 1 stereo jack adapter assembly connector.


c.
E289734C08
1.49,0.115 1.917,0.333 0.427,0.219 1.51,2.323 1.938,2.542 0.427,0.219 1.01,0.906 1.583,1.26 false 0.938,1.792 1.594,1.438 false 1.833,1.271 2.396,1 false 1.833,1.427 2.385,1.729 false 1.781,1.552 2.104,1.938 false 1.792,3.448 2.5,3.646 false 1.104,3.688 1.635,3.448 false 1.781,3.552 2.313,3.865 false 0.625,0.729 1.24,0.927 0.615,0.198 10 false UGD1 0.135,0.125 0.75,0.323 0.615,0.198 10 false *a 1.573,0.146 2.188,0.344 0.615,0.198 10 false I156 0.583,1.771 1.198,1.969 0.615,0.198 10 false US1+ 2.115,1.948 2.729,2.146 0.615,0.198 10 false USG1 2.438,1.688 3.052,1.885 0.615,0.198 10 false US1- 2.438,0.875 3.052,1.073 0.615,0.198 10 false USV1 1.604,2.354 2.219,2.552 0.615,0.198 10 false I146 0.156,2.354 0.771,2.552 0.615,0.198 10 false *b 2.552,3.583 3.167,3.781 0.615,0.198 10 false UDO+ 0.74,3.667 1.354,3.865 0.615,0.198 10 false UDO- 2.344,3.813 2.958,4.01 0.615,0.198 10 false UJSS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I156-2 (US1-) - I146-2 (UDO-) Always Below 1 Ω
I156-3 (US1+) - I146-3 (UDO+) Always Below 1 Ω
I156-5 (USG1) - I146-5 (UJSS) Always Below 1 Ω
I156-2 (US1-) - Body ground Always 10 kΩ or higher
I156-3 (US1+) - Body ground Always 10 kΩ or higher
I156-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR