The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines. Using this circuit, the radio and display receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I155 radio and display receiver assembly connector.
Disconnect the S12 roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I155-6 (SNS2) - S12-15 (SNS2) | Always | Below 1 Ω |
| I155-4 (MACC) - S12-14 (MACC) | Always | Below 1 Ω |
| I155-5 (MIN+) - S12-13 (MIC+) | Always | Below 1 Ω |
| I155-19 (MIN-) - S12-12 (MIC-) | Always | Below 1 Ω |
| I155-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| I155-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| I155-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| I155-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| I155-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I155 radio and display receiver assembly connector.
Reconnect the S12 roof console box assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I155-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I155-18 (SGND) - Body ground | Always | Below 1 Ω |
| I155-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
Roof Console Box Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 15 (SNS2) - 12 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I155 radio and display receiver assembly connector.
Reconnect the S12 roof console box assembly (telephone microphone assembly) connector.
Turn the power switch on (ACC).
| *a | Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 13 (MIC+) and 12 (MIC-) of the S12 roof console box assembly (telephone microphone assembly) connector.
Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. | B |
A
B
Replace the telephone microphone assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Check if the same malfunction recurs.
| Result | Proceed to |
|---|---|
| Malfunction does not recur (returns to normal). | A |
| Malfunction recurs. | B |
A
B