Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2015.04
RM2040EQ _56 Audio / Visual / Telematics _014716 AUDIO / VIDEO _0076806 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E287097E51
0.531,0.781 2.385,0.979 1.854,0.198 10 false from Auxiliary Battery 0.406,1.563 2.25,1.781 1.844,0.219 10 false from ACC NO. 1 Relay 0.469,2.365 2.313,2.625 1.844,0.26 10 false from IG1 NO. 2 Relay 3.406,0.948 4.25,1.177 0.844,0.229 10 false RADIO-B 3.375,1.75 5.208,1.948 1.833,0.198 10 false ECU-ACC 3.229,2.531 4.615,2.813 1.385,0.281 10 false ECU-IG1 NO. 2 5.573,3.594 6.75,4.24 1.177,0.646 10 false Radio and Display Receiver Assembly 5.438,0.792 5.75,0.99 0.313,0.198 10 false I152 5.438,1.594 5.75,1.792 0.313,0.198 10 false I152 5.427,2.375 5.74,2.573 0.313,0.198 10 false I155 5.438,3.167 5.75,3.365 0.313,0.198 10 false I152 5.521,2.99 5.833,3.188 0.313,0.198 10 false 7 5.51,2.188 5.823,2.385 0.313,0.198 10 false 1 5.51,1.385 5.823,1.583 0.313,0.198 10 false 3 5.51,0.604 5.823,0.802 0.313,0.198 10 false 4 5.802,0.792 6.26,1.021 0.458,0.229 10 false +B1 5.802,1.573 6.26,1.802 0.458,0.229 10 false ACC1 5.813,2.375 6.271,2.604 0.458,0.229 10 false IG 5.813,3.167 6.271,3.396 0.458,0.229 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the I152 and I155 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I152-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I152-4 (+B1) - I152-7 (GND1) Power switch off 11 to 14 V
I152-3 (ACC1) - I152-7 (GND1) Power switch on (ACC) 11 to 14 V
I155-1 (IG) - I152-7 (GND1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR