Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2015.04
RM2040EQ _59 Vehicle Exterior _014737 WIPER / WASHER _0075172 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Speed Signal Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a vehicle speed signal from the combination meter assembly to control the automatic windshield wiper system.

A voltage of 12 V or 5 V is output from the combination meter assembly and then input to the skid control ECU.

A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly.

Each ECU controls the respective system based on the pulse signal.

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

WIRING DIAGRAM

E237358E05
0.385,1.646 3.219,2.042 2.833,0.396 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 0.99,0.813 1.281,0.958 0.292,0.146 10 false SP1 0.052,1.646 0.375,1.823 0.323,0.177 10 false A28 0.698,6.167 2.427,6.573 1.729,0.406 10 false Stereo Component Amplifier Assembly*2 0.417,6.167 0.74,6.344 0.323,0.177 10 false I69 1.365,0.813 1.552,0.958 0.188,0.146 10 false 11 0.458,3.177 2.594,3.458 2.135,0.281 10 false Power Management Control ECU 0.458,3.021 0.75,3.188 0.292,0.167 10 false I3 1.625,2.719 2.021,2.875 0.396,0.156 10 false SPDI 2.094,2.719 2.427,2.948 0.333,0.229 10 false 16 2.938,2.719 3.115,2.875 0.177,0.156 10 false 15 3.948,2.719 4.125,2.875 0.177,0.156 10 false 18 3.948,4.24 4.125,4.396 0.177,0.156 10 false 17 2.927,4.25 3.104,4.406 0.177,0.156 10 false 20 5.385,0.813 5.688,0.958 0.302,0.146 10 false 4 5.385,2.719 5.656,2.865 0.271,0.146 10 false 3 5.604,0.896 5.802,1.042 0.198,0.146 10 false SI 5.594,2.833 5.792,2.979 0.198,0.146 10 false +S 4.99,3.219 5.281,3.479 0.292,0.26 10 false I18 5.26,3.219 7.125,3.479 1.865,0.26 10 false Combination Meter Assembly 5.573,4.24 5.896,4.385 0.323,0.146 10 false SPD 5.313,4.24 5.625,4.406 0.313,0.167 10 false 17 5.573,5.74 5.896,5.885 0.323,0.146 10 false SPD 5.302,5.74 5.49,5.906 0.188,0.167 10 false 17 4.792,6.177 5.26,6.344 0.469,0.167 10 false I67 5.031,6.167 7.115,6.354 2.083,0.188 10 false Navigation Receiver Assembly*2 2.906,5.719 3.083,5.875 0.177,0.156 10 false 19 1.708,5.729 2.031,5.875 0.323,0.146 10 false SPD 2.083,5.719 2.26,5.885 0.177,0.167 10 false 11 4.26,4.677 4.563,4.833 0.302,0.156 10 false I155 4.604,4.677 7.115,4.865 2.51,0.188 10 false Radio and Display Receiver Assembly*1 3.115,6.177 4.365,6.396 1.25,0.219 10 false Junction Connector 2.781,6.177 3.177,6.344 0.396,0.167 10 false I181 2.094,4.25 2.406,4.417 0.313,0.167 10 false 24 0.427,4.688 2.76,4.927 2.333,0.24 10 false Windshield Wiper Relay Assembly*3 0.552,7.135 2.656,7.5 2.104,0.365 10 false *1: for Radio and Display Type 2.802,7.135 4.844,7.438 2.042,0.302 10 false *2: for Navigation Receiver Type 1.719,4.333 2.042,4.479 0.323,0.146 10 false SPD 0.167,4.688 0.448,4.844 0.281,0.156 10 false I72 5.125,7.135 6.792,7.438 1.667,0.302 10 false *3: w/ Auto Wiper System

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (SPEED SENSOR SIGNAL)
a.
E277112C06
1.5,0.354 1.854,0.604 0.354,0.25 2.354,2.198 2.125,1.417 false 2.802,3.646 3.26,3.844 0.458,0.198 10 false GND 1.094,3.906 1.271,4.104 0.177,0.198 10 false A 1.604,0.396 2.063,0.594 0.458,0.198 10 false I18 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a 2.333,2.229 2.875,2.583 0.542,0.354 10 false +S
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal I18-3 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the I72 windshield wiper relay assembly connector and I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - I18-3 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I72 windshield wiper relay assembly connector and I124 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I72-24 (SPD) - I124-20 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR