Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0069-273  Manifold Absolute Pressure - Barometric Pressure Correlation  


DESCRIPTION

The atmospheric pressure sensor mounted on the MG ECU circuit board detects the atmospheric pressure. This reading is used to perform system control that considers vehicle usage conditions.

A284480E04
0.688,0.885 2.906,1.219 2.219,0.333 10 false Power Management Control ECU 1.573,2.302 2.135,2.583 0.563,0.281 10 false ECM 0.792,3.167 2.729,3.375 1.938,0.208 10 false CAN Communication Line 0.802,3.469 2.698,3.677 1.896,0.208 10 false Serial Communication Line 4.458,0.125 6.677,0.458 2.219,0.333 10 false Inverter with Converter Assembly 4.458,0.531 6.51,1 2.052,0.469 10 false MG ECU (Atmosphere Pressure Sensor) 4.531,1.208 6.469,1.615 1.938,0.406 10 false Atmosphere Pressure Sensor 4.365,1.958 6.76,2.667 2.396,0.708 10 false Manifold Absolute Pressure Sensor Assembly (Intake Air Surge Tank Assembly)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0069-273 Manifold Absolute Pressure - Barometric Pressure Correlation Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor (for EGR control) exceeds a specified value. The same condition recurs within 3 hours when driving in EV mode.
·

Inverter with converter assembly

·

Manifold absolute pressure sensor

·

ECM

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

A259008E03
0.147,2.605 0.456,2.803 0.309,0.198 10 E25 0.14,2.773 2.38,2.922 2.24,0.149 10 Manifold Absolute Pressure Sensor 6.185,3.099 6.529,3.262 0.344,0.163 10 ECM 5.632,0.98 6.08,1.129 0.448,0.149 10 VCPM 5.877,3.099 6.159,3.248 0.281,0.149 10 E28 5.371,0.98 5.548,1.129 0.177,0.149 10 78 5.371,1.554 5.559,1.724 0.188,0.17 10 79 5.371,2.093 5.575,2.243 0.204,0.149 10 80 5.632,1.554 5.9,1.703 0.267,0.149 10 PIM 5.632,2.093 6.045,2.26 0.413,0.167 10 EPIM 1.366,0.98 1.592,1.129 0.226,0.149 10 VC 1.324,1.554 1.591,1.703 0.267,0.149 10 PIM 1.394,2.093 1.592,2.26 0.198,0.167 10 E2 1.664,0.98 1.771,1.15 0.108,0.17 10 3 1.664,1.554 1.764,1.724 0.101,0.17 10 2 1.664,2.093 1.785,2.257 0.122,0.163 10 1

PROCEDURE

1.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Check if DTCs are output.

Result:
Result Proceed to
DTCs other than those listed in the following table are output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input

HINT:

P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



f.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0069-273 only is output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A-151, 658 Generator Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P2228-268 Barometric Pressure Sensor "A" Circuit Low
P2229-269 Barometric Pressure Sensor "A" Circuit High
P2511-149 ECM/PCM Power Relay Sensor Circuit Intermittent
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0100-530 Lost Communication with ECM / PCM "A"
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

3.READ VALUE USING GTS (MAP, ATMOSPHERE PRESSURE)

B

3.READ VALUE USING GTS (MAP, ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.

Powertrain > Hybrid Control > Data List
Tester Display
MAP
Atmosphere Pressure
50003 236 4,7

d.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A250945


e.

Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following. A
Difference between MAP in Data List and normal atmospheric pressure value is 10 kPa or more. B
Difference between Atmosphere Pressure in Data List and normal atmospheric pressure value is 10 kPa or more. C



f.

Turn the power switch off.



A

4.READ VALUE USING GTS (MAP)

B

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

C

REPLACE INVERTER WITH CONVERTER ASSEMBLY

4.READ VALUE USING GTS (MAP)
a.

Move the shift lever to P.


b.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP

Powertrain > Hybrid Control > Data List
Tester Display
MAP
50003 236 4

c.

Read the MAP value in the Data List with the engine stopped.


d.

While depressing the brake pedal, turn the power switch on (READY).


e.

With the READY indicator light illuminated, fully depress the accelerator pedal.


f.

Read the MAP value in the Data List with the engine running.


g.

Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.

OK:

The MAP value changes (pressure decreases when the engine is started).



h.

Turn the power switch off.

Result:
Proceed to
OK
NG




OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect connector E25 from the manifold absolute pressure sensor.


b.

Turn the power switch on (IG).


c.
A248180C13
0.542,2.042 0.938,2.302 0.396,0.26 1.469,2.385 1.156,2.927 false 1.719,2.396 1.719,2.948 false 1.979,2.396 2.365,2.948 false 0.208,0.927 0.5,1.156 0.292,0.229 10 false *a 0.615,2.104 0.906,2.25 0.292,0.146 10 false E25 1.031,2.948 1.26,3.125 0.229,0.177 10 false E2 1.604,2.969 1.938,3.167 0.333,0.198 10 false PIM 2.302,2.969 2.583,3.146 0.281,0.177 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E25-3 (VC) - E25-1 (E2) Power switch on (IG) 4.75 to 5.25 V
E25-2 (PIM) - E25-1 (E2) Power switch on (IG) 3.0 to 5.0 V



Result:
Result Proceed to
NG A
OK B


d.

Turn the power switch off.


e.

Connect the manifold absolute pressure sensor connector.



A

6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

B

7.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect connector E25 from the manifold absolute pressure sensor.


b.

Disconnect connector E28 from the ECM.


c.
A265464C02
0.594,3.552 1.083,3.844 0.49,0.292 1.833,1.823 2.323,2.115 0.49,0.292 0.74,1.469 0.427,2.188 false 0.792,1.469 0.99,2.198 false 0.854,1.469 1.552,2.188 false 1.458,3.781 1.083,4.229 false 1.656,3.792 1.656,4.25 false 1.875,3.792 2.229,4.25 false 0.094,0.031 0.281,0.208 0.188,0.177 10 false *a 0.094,2.5 0.281,2.677 0.188,0.177 10 false *b 0.188,2.208 0.656,2.406 0.469,0.198 10 false VCPM 0.896,2.208 1.25,2.438 0.354,0.229 10 false PIM 1.438,2.208 1.906,2.375 0.469,0.167 10 false EPIM 2.188,4.26 2.563,4.49 0.375,0.229 10 false VC 1.531,4.271 1.927,4.5 0.396,0.229 10 false PIM 0.958,4.24 1.281,4.458 0.323,0.219 10 false E2 0.729,3.615 1.052,3.823 0.323,0.208 10 false E25 1.958,1.896 2.333,2.146 0.375,0.25 10 false E28
*a Front view of wire harness connector
(to ECM)
*b Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E25-3 (VC) - E28-78 (VCPM) Always Below 1 Ω
E25-1 (E2) - E28-80 (EPIM) Always Below 1 Ω
E25-2 (PIM) - E28-79 (PIM) Always Below 1 Ω
E25-3 (VC) or E28-78 (VCPM) - Body ground Always 10 kΩ or higher
E25-2 (PIM) or E28-79 (PIM) - Body ground Always 10 kΩ or higher



d.

Connect the ECM connector.


e.

Connect the manifold absolute pressure sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT

8.CHECK DTC OUTPUT (HYBRID CONTROL)
8.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0069-273 is not output. A
P0069-273 is output again. B



e.

Turn the power switch off.



A

COMPLETED

B