Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0D2F-266  Drive Motor "A" Inverter Voltage Sensor Circuit Low  P0D30-267  Drive Motor "A" Inverter Voltage Sensor Circuit High  


DESCRIPTION

The inverter contains a three-phase bridge circuit, which consists of six power transistors (IGBTs) each for MG1 and MG2. The inverter converts high-voltage direct current from the HV battery into three-phase alternating current for MG1 and MG2; it also converts three-phase alternating current supplied by MG1 and MG2 into direct current for the HV battery. The MG ECU controls the actuation of the power transistors (IGBTs). The inverter transmits information necessary for control, such as amperage and voltage, to the MG ECU.

HINT:

The term "drive motor A" indicates MG2.


A259399E01
1.32,0.863 1.765,1.100 0.445,0.238 10 MG1 3.919,0.855 4.364,1.092 0.445,0.238 10 MG2 1.204,1.46 1.506,1.737 0.303,0.277 10 U 1.502,1.465 1.830,1.768 0.329,0.303 10 V 1.819,1.46 2.057,1.724 0.238,0.264 10 W 3.84,1.478 4.143,1.755 0.303,0.277 10 U 4.138,1.484 4.467,1.786 0.329,0.303 10 V 4.456,1.478 4.694,1.742 0.238,0.264 10 W 1.688,2.056 2.691,2.220 1.003,0.164 10 Current Sensor 4.245,2.056 5.237,2.209 0.992,0.154 10 Current Sensor 4.569,4.603 5.209,4.892 0.640,0.290 10 Inverter 5.76,5.663 7.062,6.096 1.302,0.432 10 Power Management Control ECU 0.326,5.922 1.161,6.231 0.835,0.310 10 Boost Converter 0.091,7.248 1.458,7.654 1.367,0.406 10 Inverter with Converter Assembly 1.583,8.295 2.353,8.533 0.770,0.238 10 HV Battery 3.155,7.85 4.080,8.075 0.926,0.225 10 A/C Inverter 3.076,6.043 3.729,6.281 0.653,0.238 10 MG ECU 4.006,6.357 5.165,6.569 1.159,0.212 10 DCDC Converter

The MG ECU uses an inverter voltage sensor, which is built into the inverter, to detect boosted high voltage to allow control of the voltage boost.

The MG ECU monitors the inverter voltage sensor and detects the following malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low Short to GND in the inverter voltage (VH) signal line Inverter with converter assembly Comes on Master Warning Light:
Comes on
P0D30-267 Drive Motor "A" Inverter Voltage Sensor Circuit High Open or short to +B in the inverter voltage (VH) signal line Inverter with converter assembly Comes on Master Warning Light:
Comes on

PROCEDURE

1.REPLACE INVERTER WITH CONVERTER ASSEMBLY

(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>COMPONENTS)

HINT:

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU inside the inverter with converter assembly. If P0D2F-266 or P0D30-267 is output, replace the inverter with converter assembly.


Result:
Proceed to
NEXT



NEXT

COMPLETED