The battery smart unit (battery energy control module) sends HV battery voltage information to the power management control ECU via serial communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0B23-129 | Hybrid Battery "A" Voltage | HV battery voltage circuit malfunction | Battery smart unit | Comes on | Master Warning Light:
Comes on |
Performing the check procedures for a long time with the shift lever in N may cause DTC P3000-388 to be set.
If, after performing troubleshooting, it is necessary to replace the battery smart unit, voltages need to be confirmed after installing the new battery smart unit. Confirm that "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" in the Data List are 280 V or more with the power switch on (READY), shift lever in P, and the engine stopped. When the system is normal, the "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" values should be almost equal (voltage boosting will not occur when the shift lever is in N). If the difference between each voltage exceeds the values specified below, there is a malfunction in the inverter with converter assembly.
| Inspection voltage | Maximum voltage difference |
|---|---|
| Difference between "Power Resource VB" and "VL-Voltage before Boosting" | 40 V |
| Difference between "Power Resource VB" and "VH-Voltage after Boosting" | 40 V |
| Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" | 50 V |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0B23-129 only is output. | A |
| DTCs shown in Table 1 are output simultaneously. | B |
| DTCs shown in Table 2 are output simultaneously. | C |
| DTC No. | Relevant Diagnosis |
|---|---|
| P06E6-164 | Sensor Power Supply "C" Circuit / Open |
| P0A1A-151, 658 | Generator Control Module |
| P0A1B-786 | Drive Motor "A" Control Module |
| P0A1D-148 | Hybrid Powertrain Control Module |
| P0D2F-266 | Drive Motor "A" Inverter Voltage Sensor Circuit Low |
| P0D30-267 | Drive Motor "A" Inverter Voltage Sensor Circuit High |
| P0E33-589 | DC/DC Converter Voltage Sensor "A" Low |
| P0E34-590 | DC/DC Converter Voltage Sensor "A" High |
| P1C2A-155 | Generator A/D Converter Circuit |
| P1C73-512 | Sensor Standard Voltage "F" Circuit / Open |
| P1CA6-156 | Generator Control Module Malfunction |
| P1CA7-193 | Drive Motor Control Module Malfunction |
| P2511-149 | ECM/PCM Power Relay Sense Circuit Intermittent |
| P3004-132 | High Voltage Power Resource |
| P3133-659 | Communication Error from Generator to Drive Motor "A" |
| P3134-661 | Communication Error from Drive Motor "A" to Generator |
| P324E-788 | MG-ECU Power Relay Intermittent Circuit |
| U0110 (all INF codes)*1 | Lost Communication with Drive Motor Control Module "A" |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0AFC-123 | Hybrid Battery Pack Sensor Module |
| P0B3D-123 | Hybrid Battery Voltage Sensor "A" Circuit Low |
| P0B42-123 | Hybrid Battery Voltage Sensor "B" Circuit Low |
| P0B47-123 | Hybrid Battery Voltage Sensor "C" Circuit Low |
| P0B4C-123 | Hybrid Battery Voltage Sensor "D" Circuit Low |
| P0B51-123 | Hybrid Battery Voltage Sensor "E" Circuit Low |
| P0B56-123 | Hybrid Battery Voltage Sensor "F" Circuit Low |
| P0B5B-123 | Hybrid Battery Voltage Sensor "G" Circuit Low |
| P0B60-123 | Hybrid Battery Voltage Sensor "H" Circuit Low |
| P0B65-123 | Hybrid Battery Voltage Sensor "I" Circuit Low |
| P0B6A-123 | Hybrid Battery Voltage Sensor "J" Circuit Low |
| P0B6F-123 | Hybrid Battery Voltage Sensor "K" Circuit Low |
| P0B74-123 | Hybrid Battery Voltage Sensor "L" Circuit Low |
| P0B79-123 | Hybrid Battery Voltage Sensor "M" Circuit Low |
| P0B7E-123 | Hybrid Battery Voltage Sensor "N" Circuit Low |
| P0B83-123 | Hybrid Battery Voltage Sensor "O" Circuit Low |
| P0B88-123 | Hybrid Battery Voltage Sensor "P" Circuit Low |
| P0B8D-123 | Hybrid Battery Voltage Sensor "Q" Circuit Low |
| P0B92-123 | Hybrid Battery Voltage Sensor "R" Circuit Low |
| P308A-123 | Hybrid Battery Voltage Sensor All Circuits Low |
*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
P0B23-129 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.
Turn the power switch off.
A
B
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
C
(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)