Home › Vehicle Interior › POWER OUTLETS (INT) › WIRELESS CHARGING SYSTEM › from 2016.05
RM2040EQ _58 Vehicle Interior _014731 POWER OUTLETS (INT) _0269992 WIRELESS CHARGING SYSTEM J

POWER OUTLETS (INT)  WIRELESS CHARGING SYSTEM  Status Signal Circuit  


DESCRIPTION

This circuit sends a charging suspension signal from the certification ECU (smart key ECU assembly) to the mobile wireless charger cradle assembly. Based on this signal, the mobile wireless charger cradle assembly suspends or resumes wireless charging.

HINT:

The wireless charging system uses the same radio wave frequency that is used to perform verification of the electrical key transmitter sub-assembly. Therefore, when the electrical key transmitter sub-assembly verification is being performed, the certification ECU (smart key ECU assembly) sends a charging suspension signal to the wireless charging system to suspend charging.


WIRING DIAGRAM

E215956E31
4.615,0.833 4.927,1.031 0.313,0.198 10 false 7 2.438,0.833 2.75,1.031 0.313,0.198 10 false 16 4.802,0.948 5.115,1.146 0.313,0.198 10 false DIS 1.948,0.948 2.51,1.156 0.563,0.208 10 false ASEL 1.125,1.292 1.438,1.49 0.313,0.198 10 false O2 4.625,1.281 4.938,1.479 0.313,0.198 10 false I183 1.115,1.458 2.74,1.844 1.625,0.385 10 false Certification ECU (Smart Key ECU Assembly) 4.615,1.448 6.198,1.813 1.583,0.365 10 false Mobile Wireless Charger Cradle Assembly

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (DIS)
a.
E216116C19
1.542,0.302 1.865,0.51 0.323,0.208 2.104,1.396 2.542,1.594 false 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 1.573,0.313 1.885,0.51 0.313,0.198 10 false I183 2.583,1.542 3.042,1.74 0.458,0.198 10 false DIS
*a Component with harness connected
(Mobile Wireless Charger Cradle Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: When the power switch is turned from off to on (ACC), the mobile wireless charger cradle assembly monitors the charging suspension signal for 5 seconds. If the charging suspension signal is not 4 V or more for 0.8 seconds or more during monitoring, the mobile wireless charger cradle assembly determines that there is an open in the charging suspension signal line, blinks (pattern 1) the indicator light (amber), and prohibits operation until the power switch is turned from off to on (ACC) again.

*2: For details about conditions when the certification ECU (smart key ECU assembly) sends the charging suspension signal, refer to System Description.

Click here(Click here)

I183-7 (DIS) - Body ground For 5 seconds after turning power switch from off to on (ACC)*1 4.5 to 6.0 V
Device being charged Below 1 V
Charging suspended due to smart entry and start system status*2 4.5 to 6.0 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (MOBILE WIRELESS CHARGER CRADLE ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I183 mobile wireless charger cradle assembly connector.


b.

Disconnect the O2 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I183-7 (DIS) - O2-16 (ASEL) Always Below 1 Ω
I183-7 (DIS) or O2-16 (ASEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR