SMART ENTRY AND START SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
The main components for the start function have the following functions:
| Component | Function | |
Power Switch
|
| |
| Electrical Key Transmitter Sub-assembly | Receives the signals from the antennas and returns the ID code to the door control receiver. | |
Indoor Electrical Key Antenna
| Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle. | |
| Door Control Receiver | Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly). | |
| Certification ECU (Smart Key ECU Assembly) |
| |
| Power Management Control ECU |
| |
| Stop Light Switch Assembly | Outputs the state of the brake pedal to the certification ECU (smart key ECU assembly). | |
| Steering Lock ECU (Steering Lock Actuator Assembly) | Receives the steering wheel unlock/lock request signal from the certification ECU (smart key ECU assembly), and activates the steering lock motor. | |
| Combination Meter Assembly | Buzzer | Sounds to inform the driver of malfunctions in the smart entry and start system. |
| Multi-information Display | The following warning messages appear to alert the driver.
| |
The main components for the entry function have the following functions:
| Component | Function | |
| Electrical Key Transmitter Sub-assembly |
| |
| Main Body ECU (Multiplex Network Body ECU) |
| |
| Certification ECU (Smart Key ECU Assembly) |
| |
| Outside Door Handle | Door Electrical Key Antenna | Receives a request signal from the certification ECU (smart key ECU assembly), and creates an actuation area around each front door. |
| Lock Sensor | Transmits door lock request signals to the certification ECU (smart key ECU assembly). | |
| Touch Sensor | Detects when a person touches the inside of an outer door handle. | |
| Outside Electrical Key Antenna (Luggage Compartment Door) | Receives a request signal from the certification ECU (smart key ECU assembly), and forms an actuation area around the luggage compartment door. | |
Indoor Electrical Key Antenna
| Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area in the vehicle. | |
| Door Control Receiver | Receives the ID code from the electrical key transmitter sub-assembly and transmits it to the certification ECU (smart key ECU assembly). | |
| Luggage Compartment Door Open Switch | Transmits a luggage compartment door open request signal to the certification ECU (smart key ECU assembly). | |
| Combination Meter Assembly | Buzzer | Sounds to inform the driver of malfunctions in the smart entry and start system. |
| Multi-information Display | The following warning messages appear to alert the driver.
| |
| Wireless Door Lock Buzzer |
| |
| OPERATION |
The special functions of the smart entry and start system only work when the electrical key transmitter sub-assembly is in the actuation area formed by the antennas.
The indoor electrical key antenna (front), indoor electrical key antenna (rear), and indoor electrical key antenna (luggage compartment) form the interior actuation area.
The door electrical key antenna LH, door electrical key antenna RH, and outside electrical key antenna (luggage compartment door) form the exterior actuation area.

| *1 | Indoor Electrical Key Antenna (Front) | *2 | Door Electrical Key Antenna LH |
| *3 | Door Electrical Key Antenna RH | *4 | Indoor Electrical Key Antenna (Rear) |
| *5 | Indoor Electrical Key Antenna (Luggage Compartment) | *6 | Outside Electrical Key Antenna (Luggage Compartment Door) |
| *7 | Electrical Key Transmitter Sub-assembly | - | - |
| *a | Approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) | - | - |
![]() | Interior Actuation Area | ![]() | Exterior Actuation Area |
| Actuation Area | Detail |
| Interior | The interior actuation area of the indoor electrical key antennas (front, rear) is formed when the driver door is opened or closed, when the power switch is pushed, when a warning is activated, or when a lock sensor is on. |
| Exterior | The exterior actuation area formed by the door electrical key antennas (LH, RH) and outside electrical key antenna (luggage compartment door) is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handle of the front doors, or the center of the rear bumper. |
| Around Front Doors | The exterior actuation area of the door electrical key antennas (LH, RH) is formed by transmitting a request signal every 0.25 seconds while the power switch is off and each door is locked. In this way it detects the presence of an electrical key transmitter sub-assembly. When locking the door using the lock sensor on the outer door handle, the actuation area is formed when the lock sensor is touched. |
| Around Luggage Compartment Door | The exterior actuation area of the outside electrical key antenna (luggage compartment door) is formed when the luggage compartment door open switch is on. |
| SYSTEM CONTROL |
Start Function
The start function has different power source change patterns to suit the brake pedal state and shift lever position.
| Pattern | Brake Pedal | Shift Lever Position | Power Source Change Pattern |
| A | Depressed | P or N | When the power switch is pushed once.
|
| B | Not Depressed | P | Each time the power switch is pushed.
|
| C | Except P | Each time the power switch is pushed.
| |
| D | - | P | When the power switch is pushed in the on (IG) condition.
|
| E | - | Except P | When the power switch is pushed in the on (IG) condition.
|

Entry Unlock
While the user carries the electrical key transmitter sub-assembly in the exterior actuation area, and a front door outside handle is held (the back side of the handle is touched), the door unlock sensor built into the handle detects it and the doors are unlocked.
When the doors are unlocked, the hazard warning lights flash twice as an answer back.

| *1 | Unlock Sensor | - | - |
Entry Lock
When the user gets out of the vehicle while carrying the electrical key transmitter sub-assembly and touches the lock sensor of the door outside handle within the exterior actuation area with all the doors closed, the doors are locked.

| *1 | Lock Sensor | - | - |
Luggage Compartment Door Open
The luggage compartment door is opened when the luggage compartment door opener switch is pressed within the luggage compartment door exterior actuation area while the user is carrying the electrical key transmitter sub-assembly.

| *1 | Unlock Switch | - | - |
| *a | Approximately 0.7 m (2.30 ft.) | - | - |
Warning
When any of the situations below occur, the smart entry and start system sounds the wireless door lock buzzer, sounds a buzzer in the combination meter assembly and displays a message on the multi-information display in order to alert the driver.
| Situation | Condition |
| A | The hybrid system is left running and the shift lever is in a position other than P when the driver gets out of the vehicle. |
| B | The key reminder sounds. |
| C | The hybrid system is left running and the shift lever is in P when the driver gets out of the vehicle. |
| D | The hybrid system is left running when a passenger gets out of the vehicle while holding the electrical key transmitter sub-assembly. |
| E | The electrical key transmitter sub-assembly is not within the actuation areas. |
| F | The vehicle is driven without an electrical key transmitter sub-assembly. |
| G | The electrical key transmitter sub-assembly is left in the vehicle. |
| H | A door is ajar. |
| I | The vehicle has started off with an electrical key transmitter sub-assembly in the luggage compartment. |
| J | The key battery is weak. |
| K | Steering lock does not release. |
| L | A malfunction has been detected in a circuit, vehicle speed signal, etc. |
| M | The hybrid system cannot be started (system error) |
| N | The hybrid system cannot be started (driver error) |
| O | An attempt has been made to turn off the vehicle with the shift lever in a position other than P. |
| P | Auto power off operation occurs. |
| Q | Immobiliser system certification confirmation occurs. |
Situation A
| Possible Effects without Warning | Sudden vehicle movement, Vehicle theft, Vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effects without Warning | Sudden vehicle start-off, Vehicle theft, Vehicle roll-away | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously |
| Multi-information Display | The following warning messages are alternately displayed:
| ||
| Wireless Door Lock Buzzer | Sounds continuously | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met: | ||
| Combination Meter Assembly | Buzzer |
| |
| Wireless Door Lock Buzzer | |||
| Combination Meter Assembly | Multi-information Display ("Key not detected" message displayed) |
| |
| Multi-information Display ("Shift to P position when parked" message displayed) |
| ||
Situation B
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | Pattern 1 The warning is activated when both of the following conditions are met: - The power switch is on (ACC). - The driver door is open. Pattern 2 The warning is activated when all of the following conditions are met: - The power switch is turned from on (IG) to off. - The driver door is open. - The steering lock remains unlocked. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds continuously at short and even intervals |
| Multi-information Display | - | ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation C
| Possible Effects without Warning | Vehicle theft, Hybrid system cannot be restarted, Discharged battery | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer | Sounds 3 times | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| Possible Effects without Warning | Vehicle theft, Discharged battery | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning messages are alternately displayed:
| ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met: | ||
| Combination Meter Assembly | Multi-information Display ("Turn Power OFF" message displayed) |
| |
| Multi-information Display ("Key not detected" message displayed) |
| ||
| Wireless Door Lock Buzzer |
| ||
Situation D
| Possible Effect without Warning | Hybrid system cannot be restarted. | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer | Sounds 3 times | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation E
| Possible Effect without Warning | User becomes confused | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The electrical key transmitter sub-assembly is detected again or returned to the vehicle. | ||
Situation F
| Possible Effect without Warning | Hybrid system cannot be restarted. | ||
| Warning Active Condition |
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds nine times |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation G
| Possible Effect without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The warning is stopped when any of the following conditions is met: | ||
| Combination Meter Assembly | Multi-information Display |
| |
| Wireless Door Lock Buzzer |
| ||
| Possible Effect without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | Sounds for 5 seconds | ||
| Warning Stop Condition | The electrical key transmitter sub-assembly is removed from the vehicle and the lock sensor is on. | ||
| Combination Meter Assembly | Multi-information Display |
| |
| Wireless Door Lock Buzzer |
| ||
Situation H
| Possible Effects without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | - | ||
| Wireless Door Lock Buzzer | Sounds continuously | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation I
| Possible Effect without Warning | Vehicle theft | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | - | ||
| Wireless Door Lock Buzzer | Sounds continuously for 5 seconds. | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation J
| Possible Effect without Warning | Smart entry and start system does not function | ||
| Warning Active Condition | Condition 1: The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation K
| Possible Effect without Warning | Steering usability function, the hybrid system cannot be started. | ||
| Warning Active Condition | The steering lock cannot be released. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The power switch is pushed while the steering wheel is turned left and right, and the steering lock successfully disengages. | ||
Situation L
| Possible Effect without Warning | Usability function | ||
| Warning Active Condition | The warning is activated when one of the following conditions is met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 15 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The system returns to normal. | ||
Situation M
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 60 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation N
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The power switch is turned off or on (IG). | ||
| Possible Effect without Warning | Usability function (user cannot start vehicle) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Situation O
| Possible Effect without Warning | Usability function (user becomes confused) | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
| Possible Effect without Warning | Discharged battery, Vehicle roll-away | ||
| Warning Active Condition | After the power switch is turned off with the shift lever in any position other than P, the shift lever is moved to P. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed:
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when either of the following conditions is met:
| ||
Situation P
| Possible Effect without Warning | Vehicle battery discharges | ||
| Warning Active Condition | The warning is activated when all of the following conditions are met:
| ||
| Warning Method | Combination Meter Assembly | Buzzer | - |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The power switch is turned to a mode other than off. | ||
Situation Q
| Possible Effect without Warning | Malfunction detection | ||
| Warning Active Condition | Key certification result is OK. | ||
| Warning Method | Combination Meter Assembly | Buzzer | Sounds once |
| Multi-information Display | The following warning message is displayed for 10 seconds (and then automatically turned off).
| ||
| Wireless Door Lock Buzzer | - | ||
| Warning Stop Condition | The warning is stopped when one of the following conditions is met:
| ||
Battery Saving
Battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the electrical key transmitter sub-assembly is left in the exterior actuation area.
| Condition | Control | Reinstatement Condition |
| When the vehicle remains parked for a long time. | Condition 1:
| When the power switch is turned on (IG), the control is canceled and the system is returned to normal. |
Condition 2:
| When the power switch is turned on (IG), the control is canceled and the system is returned to normal.
| |
| When the electrical key transmitter sub-assembly is left in the exterior detection area. |
|
|
In addition to the above functions, the auto power off function helps to reduce drain on the vehicle auxiliary battery by turning the power source mode to off when approximately 60 minutes have elapsed since (a) the shift lever was moved to P with the power source on (ACC), or (b) the hybrid system was turned off with the shift lever in P, the power source on (IG) and the vehicle stationary.
Battery Saving Function of Electrical Key Transmitter Sub-assembly
This function cancels the signal reception waiting state of the electrical key transmitter sub-assembly, reducing the consumption of current from its battery.
The electrical key transmitter sub-assembly can be placed into and taken out of battery saving mode. When the electrical key transmitter sub-assembly is in battery saving mode, the smart entry and start system will not be able to detect the transmitter, as the transmitter will not respond to signals from the vehicle. The smart entry and start function will not operate if the electrical key transmitter sub-assembly is in battery saving mode.
Pressing the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch (the indicator light of the electrical key transmitter sub-assembly blinks 4 times) selects battery saving mode for the electrical key transmitter sub-assembly.
Battery saving mode can be canceled by pressing any switch on the electrical key transmitter sub-assembly.
Key Cancel
The following system functions can be deactivated by using the key cancel procedure.
The system functions can be deactivated by using the following key cancel procedure when the power switch is off and the driver door is closed and unlocked.
| Key Cancel Procedure |
|
Key Code Registration Function
The table below shows the 4 special ID code registration function modes through which up to 7 different transmitter recognition codes can be registered. The codes are electronically registered (written to and stored) in the EEPROM. For details, refer to the Service Bulletin.
| Mode | Function |
| Rewrite | Clears all previously registered codes and registers only the newly received codes. This mode is used whenever a transmitter or the certification ECU (smart key ECU Assembly) is replaced. |
| Add | Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter. If the number of codes exceeds 7, the oldest registered code is cleared first. |
| Confirm | Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist. |
| Prohibit | To clear all the registered codes and to prohibit the wireless door lock function. This mode is used when an electrical key transmitter sub-assembly is lost. |
| FUNCTION |
Entry Function
The entry function consists of the following functions:
| Function | Outline |
| Wireless Door Lock Control | This function is a convenient system for locking and unlocking all the doors and luggage compartment door at a distance. The operation of this function is the same as that in the wireless door lock control system. |
| Entry Illumination | When an electrical key transmitter sub-assembly enters the exterior actuation area of the door electrical key antennas (LH and RH), the interior light illuminate. |
| Entry Unlock | When an electrical key transmitter sub-assembly is located in the exterior actuation area of any door electrical key antenna, the door will unlock after the inner part of either front outside door handle is touched.
|
| Entry Unlock Mode Switching | Allows switching between 2 modes that can be operated with the entry unlock function.
|
| Entry Lock | When an electrical key transmitter sub-assembly is located in the exterior actuation area of an electrical key antenna (driver or front passenger door) and the power switch is off, all doors can be locked by simply touching the lock sensor. |
| Luggage Compartment Door Open | When an electrical key transmitter sub-assembly is in the exterior actuation area of the outside electrical key antenna (luggage compartment door), the luggage compartment door opens manually by simply pushing the luggage compartment door open switch. |
| Prevention of Key Confinement | The key confinement prevention function prevents the vehicle from being locked with an electrical key transmitter sub-assembly left inside it. This function operates in 2 different situations: when the lock knob is used (keyless lock) and when an outside door handle lock sensor is used (lock sensor). |
| Warning | When any of the situations below occur, the smart entry and start system causes the certification ECU (smart key ECU assembly) to sound the buzzer in the combination meter and the wireless door lock buzzer, and indicates a warning on the multi-information display in order to alert the driver.
|
| Battery Saving | If the electrical key transmitter sub-assembly remains within the exterior actuation area of any electrical key antenna (driver, front passenger, or luggage compartment door), the system maintains periodic communication with the electrical key transmitter sub-assembly. Therefore, if the vehicle remains parked in that state for a long time, the key battery and the vehicle battery could be drained. |
| Key Cancel | The following key functions can be canceled by following the specified procedure.
|
| Key Code Registration | A total of 7 electrical key transmitter sub-assemblies can be registered. Key registration enables the registering (writing and storing) of transmitter recognition codes in the EEPROM that is contained in the certification ECU (smart key ECU assembly). |
The wireless door lock control system allows the following customizable functions:
| Function | Outline | Customizable*1 |
| All Doors Lock | Pressing the lock button of the electrical key transmitter sub-assembly locks all doors. | Standard (Not Customizable) |
| All Doors Unlock (2-step Unlock) | Pressing the unlock button of the electrical key transmitter sub-assembly twice within 5 seconds unlocks all doors after it first unlocks the driver's door. | *3 |
| All Doors Unlock (1-step Unlock) | Pressing the unlock button of the electrical key transmitter sub-assembly once unlocks all doors. | *2 |
| Luggage Compartment Door Open | Keeping the luggage compartment door button of the electrical key transmitter sub-assembly pushed longer than about 0.8 seconds opens the luggage compartment door. | *2 |
| Answer Back | When the doors are being locked or unlocked using the electrical key transmitter sub-assembly, the wireless door lock buzzer sounds and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function. | *2 |
| Automatic Relock | If none of the doors are opened within 30 seconds after they are unlocked using the wireless door lock remote control, all the doors will be locked again automatically. | *2 |
| Repeat | If a door is not locked in response to the locking operation of the electrical key transmitter sub-assembly, the main body ECU (multiplex network body ECU) will output a lock signal again after 1 second elapses. | Standard (Not Customizable) |
| Security | Sends a door lock/unlock operation request signal as a rolling code. | Standard (Not Customizable) |
| Door Ajar Warning | If any door is open or ajar, pushing the lock button of the electrical key transmitter sub-assembly will cause the wireless door lock buzzer to sound for about 5 seconds as a warning. | Standard (Not Customizable) |
| CONSTRUCTION |
Electrical Key Transmitter Sub-assembly
The electrical key transmitter sub-assembly consists of a mechanical key, transmitter for the wireless door lock control, transceiver for the entry function, and transponder chip for the engine immobiliser function.
This mechanical key operates the driver door lock cylinder, luggage compartment door lock cylinder and glove box lock cylinder, but cannot be used to start the hybrid system.
The transmitter for the wireless door lock control has a lock switch, unlock switch and luggage compartment door open switch.
The transceiver in the electrical key transmitter sub-assembly receives the signals from the antennas and returns the ID code of the electrical key transmitter sub-assembly to the door control receiver.
The transponder chip for the engine immobiliser function returns a signal to the power switch as a response to the radio wave signals received from the power switch.

| *1 | Mechanical Key | *2 | Lock Switch |
| *3 | Unlock Switch | *4 | Luggage Compartment Door Open Switch |
Power Switch
The power switch consists of a momentary type switch, illumination, antenna coil, and transponder key amplifier.

Combination Meter Assembly
When the certification ECU (smart key ECU assembly) detects an abnormality with the smart entry and start system, a message appears on the multi-information display. If the hybrid system is stopped in this state, it might not be possible to restart it.

| *a | Power ON | *b | Hybrid System Ready State |
| Power Source Condition | Multi-information Display | |
| Brake Pedal not Depressed | Brake Pedal Depressed with Shift Lever in P | |
| Off | OFF | Hybrid System Ready State |
| On (ACC), On (IG) | Power ON | Hybrid System Ready State |
| READY ON | OFF | OFF |
Power Management Control ECU
The power management control ECU includes the IG1 relay and IG2 relay actuation circuits, CPU, and hold circuit.
The hold circuit is provided to prevent the power supply to the relays from being cut off when an abnormality occurs in the IG1 relay and/or IG2 relay actuation circuits while driving.

Door Control Receiver (Multi-channel)
The electrical key transmitter sub-assembly and door control receiver can operate on 2 different RF channels. When an electrical key transmitter sub-assembly is brought within an exterior detection area, key verification begins. If key verification fails due to radio wave interference, the channel will be switched and key verification will be performed again.
The multi-channel system begins verification using the channel on which the last verification was successfully performed. When verification fails, the system switches to the other channel.

| *a | Exterior detection areas are created using LF waves (emitted from the vehicle at intervals of 0.25 seconds) to receive a response from the electrical key transmitter sub-assembly. |
| *b | When the electrical key transmitter sub-assembly is brought into an exterior detection area, it receives LF waves from the vehicle. Using RF waves, the electrical key transmitter sub-assembly responds to the vehicle. |
| *c | Upon receiving the response from the electrical key transmitter sub-assembly, the certification ECU (smart key ECU assembly) activates the electrical key antennas (outside) one by one. Using LF waves, the certification ECU (smart key ECU assembly) determines which exterior detection area the electrical key transmitter sub-assembly is in. |
| *d | The electrical key transmitter sub-assembly receives the LF waves from the vehicle and responds using RF waves. (The certification ECU (smart key ECU assembly) recognizes which exterior detection area the electrical key transmitter sub-assembly is in.) |
| *e | The certification ECU (smart key ECU assembly) sends registered key ID information to the electrical key transmitter sub-assembly using LF waves. (Up to 7 key IDs can be registered.) |
| *f | The electrical key transmitter sub-assembly sends the key ID information using RF waves. When the certification ECU (smart key ECU assembly) receives it, verification completes. |
| *g | Radio wave interference (channel switching) |
| *b or *d is NG | *f is NG | |||
| Condition | RF waves cannot be received | RF waves cannot be received properly | RF waves cannot be received | RF waves cannot be received properly |
| Channel switching | Channels will not be switched. | Channels will be switched. | Channels will be switched. | Channels will be switched. |
| DIAGNOSIS |
Start Function
The power management control ECU can detect malfunctions in the smart entry and start system when the power source is on (IG).
When the ECU detects a malfunction, a message appears on the multi-information display to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.
The indicator light warning continues for 15 seconds even after the power switch is turned off.
The 5-digit DTCs can be read by connecting the Global TechStream (GTS) to the DLC3.
The smart entry and start system may not operate successfully if a malfunction occurs.