CRUISE CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components in the cruise control system have the following functions:

    Component
    Function
    Cruise Control Switch
    ON-OFF Button
    Turns the cruise control system on and off.
    CANCEL Switch
    A cancel signal can be output to the power management control ECU through the operation of this switch.
    +RES Switch
    The accelerate function and resuming of a preset speed can be performed by operating this switch. A signal is output to the power management control ECU when this switch is operated.
    -SET Switch
    The decelerate function and vehicle speed setting signals are output to the power management control ECU due to operation of this switch.
    Power Management Control ECU
    Controls all functions of the cruise control system in accordance with the signals from switches, sensors and ECUs.
    Inverter with Converter Assembly
    MG ECU
    Built into the inverter with converter assembly. Controls the motive force of MG2 in accordance with signals from the power management control ECU.
    ECM
    Actuates the throttle control motor in accordance with the signals from the power management control ECU.
    Skid Control ECU
    Transmits the VSC operation signal to the power management control ECU.
    Combination Meter Assembly
    Cruise Control Indicator Light
    1. Based on a cruise control indicator operation signal sent by the power management control ECU, the combination meter assembly illuminates the cruise control indicator light when the cruise control system has been turned on using the ON-OFF button on the cruise control switch.
    2. Based on a cruise control indicator operation signal sent by the power management control ECU, the combination meter assembly turns off the cruise control indicator light if a malfunction occurs in the cruise control system.
    Cruise Control SET Indicator Light
    Illuminates when the vehicle speed is set.
    Multi-information Display
    Displays a warning message to alert the driver in accordance with a signal provided by the power management control ECU.
    Throttle Body with Motor Assembly
    Throttle Control Motor
    Adjusts the throttle valve opening angle in accordance with signals from the ECM.
    Throttle Position Sensor
    Detects the throttle valve opening angle and outputs it to the ECM.
    Speed Sensor
    Detects the wheel speed of each of the 4 wheels.
    Accelerator Pedal Sensor Assembly
    Detects the accelerator pedal depression degree and outputs it to the power management control ECU.
    Shift Lever Position Sensor
    Detects the shift lever position and transmits signals to the power management control ECU.
    Stop Light Switch Assembly
    Detects the brake pedal being depressed and transmits its signal to the power management control ECU.


FUNCTION
  1. The cruise control system has the following control functions:

    Function
    Outline
    Constant Speed Control
    The power management control ECU compares the actual vehicle speed with the set speed. If the vehicle speed is higher than the set speed, the power management control ECU calculates optimal motive forces for the engine and MG2, and decelerates by adjusting the respective motive forces. If the vehicle speed is lower than the set speed, the power management control ECU calculates optimal motive forces for the engine and MG2, and accelerates by adjusting the respective motive forces.
    Set Control
    1. When this system fulfils the following conditions, and the cruise control switch is moved to the -SET side and released, the power management control ECU stores the vehicle speed and maintains the vehicle constantly at that speed.
      1. The cruise control system has been turned on using the ON-OFF button on the cruise control switch.
      2. The vehicle is being driven at a speed of approximately 40 km/h (25 mph) or more.
    Low Speed Limit Control
    The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 40 km/h (25 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control is set and working to maintain vehicle speed, the cruise control will be canceled automatically. However the set speed is kept in memory.
    COAST Switch Control
    1. When the cruise control switch is held to the -SET side, the vehicle speed and the set vehicle speed change as follows:
      1. The vehicle will decelerate.
      2. The set vehicle speed will change to the speed at which the vehicle is being driven when the COAST switch (-SET side operation) is released.
    Tap Down Control
    1. When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the -SET side, the vehicle speed and the set vehicle speed change as follows:
      1. The vehicle will decelerate in increments of approximately 1.6 km/h (1 mph) each time the switch is moved.
      2. However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven at when the switch is pushed.
    ACC Switch Control
    1. When the cruise control switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows:
      1. The vehicle will accelerate.
      2. The set vehicle speed will change to the speed at which the vehicle is being driven when the switch is released.
    Tap Up Control
    1. When the cruise control switch is moved momentarily (approximately 0.6 seconds or less) to the +RES side, the vehicle speed and the set vehicle speed change as follows:
      1. The vehicle will accelerate in increments of approximately 1.6 km/h (1 mph) each time the switch is moved.
      2. However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change.
    RES Switch Control
    If cruise control speed control operation is canceled for any reason other than a malfunction (except cancelation by operating the ON-OFF button on the cruise control switch) and the vehicle speed is more than the low speed limit, the vehicle can be returned to the speed which was stored before the cancelation of cruise operation by moving the cruise control switch to the +RES side. The stored vehicle speed can be resumed even if the vehicle speed drops below the low speed limit, because the speed in the memory has not been cleared.
    Manual Cancel Control
    1. If any of the following signals are sent to the power management control ECU, cruise control speed control operation is canceled accordingly.
      1. Stop light switch on signal (The brake pedal is depressed.)
      2. Signals indicating a change in the shift state from drive D to another state. (The shift lever is moved from D to N or B.)
      3. CANCEL switch on signal (The cruise control switch is moved to the CANCEL side.)
      4. Cruise control switch (ON-OFF button) off signal
      5. VSC operation
    Automatic Cancel Control
    1. If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
      1. Stop light switch open or short circuit
    Furthermore, the cruise control indicator light will turn off and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch, and the operation of the cruise control is disabled until the cruise control system is turned on again using the ON-OFF button.
    1. If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
      1. Malfunction in the hybrid system
    Furthermore, the operation of the cruise control is disabled until cruise control system is turned on again using the ON-OFF button.
    1. If any of the following conditions occur during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
      1. Stop light switch input signal is abnormality
      2. Cancel circuit malfunction
      3. Communication malfunction between the skid control ECU and power management control ECU
    Furthermore, the cruise control indicator light will turn off and a message indicating a malfunction will be displayed on the multi-information display until the cruise control system is turned off using the cruise control switch, and the operation of the cruise control is disabled until the power switch is turned off.
    1. If the following condition occurs during cruise control speed control operation, the speed that is set in memory is cleared and cruise control speed control operation is canceled.
      1. Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control is set.
    1. If the following condition occurs during cruise control speed control operation, cruise control speed control operation is canceled.
      1. Vehicle speed decreases below the low speed limit (approximately 40 km/h [25 mph]).


CONSTRUCTION


  1. Cruise Control Switch

    1. The cruise control switch consists of the ON-OFF button and the +RES, -SET and CANCEL switches. The +RES, -SET and CANCEL switches are operated by moving the lever in the 3 directions indicated.



    2. The switches in the cruise control switch are of the automatic reset (normally open) type that turn on only when the switch is being operated and turn off as soon as the driver releases the switch. Furthermore, the functions of the switches are active only when the cruise control system has been turned on using the ON-OFF button on the cruise control switch.


      X106262E01


      Text in Illustration 
      *1
      Cruise Control Switch
      -
      -
      *a
      ON-OFF Button
      *b
      +RES Switch
      *c
      -SET Switch
      *d
      CANCEL Switch


OPERATION
  1. Combination Meter Assembly

    1. The combination meter assembly provides a cruise control indicator light and cruise control SET indicator light to indicate the condition of the cruise control system.

      Condition
      Multi-information Display
      Y111731
      Y111733
      Set Standby
      -
      Illuminates
      Does not illuminate
      Being Controlled
      -
      Illuminates
      Illuminates
      System Malfunction
      Y113782
      Turns off
      Turns off


DIAGNOSIS
  1. If a malfunction occurs in the cruise control system during cruise control operation, the ECM automatically cancels control and turns off both the cruise control indicator light and the cruise control SET indicator light. At this time, "CHECK CRUISE CONTROL SYSTEM" is displayed on the multi-information display. At this time, the ECM stores the malfunction in the form of a 5-digit Diagnostic Trouble Code (DTC).

  2. The 5-digit DTC can be read by connecting the intelligent tester to DLC3. For details, refer to the Repair Manual.