EMISSION CONTROL SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the 2AR-FXE emission control system are as follows:

    Component
    Function
    TWC
    Oxidizes CO and HC in the exhaust gas and deoxidizes NOx at the same time, to purify them into CO2, H2O and N2.
    Air Fuel Ratio Sensor
    Is used to determine the concentration of oxygen remaining in the exhaust gas. Has a characteristic where its output is proportional to the engine air fuel ratio. Located upstream of the catalytic converter. For details Click here.
    Oxygen Sensor
    The signal of the air fuel ratio sensor changes abruptly between lean and rich at the stoichiometric air fuel ratio. Located downstream of the catalytic converter. For details Click here.
    E.F.I. Vacuum Sensor Assembly
    Uses built-in semiconductors to detect the intake manifold pressure.
    EGR Valve Assembly*
    Operates when receiving signals from the ECM, regulating the EGR volume.
    EGR Cooler*
    Cools the exhaust gas temperature to improve the EGR efficiency.
    ECM
    1. Controls the volume of fuel injected, with corrections based primarily on the signal from the air fuel ratio sensor, and minor corrections based on the signal from the oxygen sensor. This control optimizes the air-fuel ratio.
    2. Regulates the EGR volume in accordance with the various sensor signals.*
    Charcoal Canister Assembly
    Contains activated charcoal to absorb the fuel vapor that is created in the fuel tank assembly.
    Fresh Air Line
    Fresh air goes into the charcoal canister assembly and the cleaned drain air goes out into the atmosphere.
    Purge VSV
    Opens in accordance with the signals from the ECM when the system is purging in order to send the fuel vapor that was absorbed by the charcoal canister assembly into the intake manifold. In system monitoring mode, this valve controls the introduction of vacuum into the fuel tank assembly.
    Canister Filter
    Prevents dust and debris in fresh air from entering the system.
    *: Models with EGR control


SYSTEM CONTROL


  1. EGR Control (Models with EGR Control)

    1. For the EGR system, a regulated amount of inert gas is allowed to flow into the intake passage, reducing the peak temperature in the engine combustion chamber.



    2. By sensing the engine driving conditions and actual amount of the EGR valve opening, the ECM operates the EGR valve and throttle control motor, to regulate the amount of exhaust gas that is recirculated.


      W107262E01



  2. Purge Flow Control

    1. When the engine has reached predetermined state (close loop, engine coolant temperature above 80°C (176°F), etc), stored fuel vapor is purged from the charcoal canister assembly whenever the purge VSV is opened by the ECM.



    2. The ECM will change the duty ratio cycle of the purge VSV, thus controlling purge flow volume. Purge flow volume is determined by intake manifold pressure and the duty ratio cycle of the purge VSV. Atmospheric pressure is allowed into the charcoal canister assembly to ensure that purge flow is constantly maintained whenever purge vacuum is applied to the charcoal canister assembly.


      W100095E02


CONSTRUCTION


  1. Three-Way Catalytic converter (TWC)

    1. TWCs are provided in the exhaust manifold sub-assembly and also in the front exhaust pipe assembly.

    2. An exhaust manifold with an integrated TWC is used for improved warm-up of the TWC in the front exhaust pipe assembly.

    3. An ultra thin-wall, high-cell density, ceramic type TWC is used for the exhaust manifold sub-assembly and a thin-wall, ceramic type TWC is used for the front exhaust pipe assembly.



    4. The ultra thin-wall TWC enables improved exhaust emissions through optimized cell density and wall thickness.


      W105836E01


      Text in Illustration 
      *1
      Exhaust Manifold Sub-assembly
      *2
      TWC
      *3
      Ultra Thin-wall
      *4
      Front Exhaust Pipe Assembly



  2. EGR Valve and EGR Cooler (Models with EGR Control)

    1. A step motor type EGR valve is used to precisely control the EGR gas flow amount.



    2. The EGR cooler cools the exhaust gas to improve the EGR efficiency.


      W105615E01


      Text in Illustration 
      *1
      Water Passage
      *2
      EGR Gas Passage
      *3
      EGR Valve Assembly
      *4
      No. 1 EGR Pipe
      *5
      EGR Cooler Assembly
      *6
      No. 2 EGR Pipe
      *a
      To EGR Valve Assembly
      *b
      From Exhaust Manifold
      *c
      A-A Cross Section
      -
      -
      V100135
      EGR Gas
      -
      -



  3. E.F.I. Vacuum Sensor Assembly

    1. An E.F.I. vacuum sensor assembly is used to measure the intake manifold pressure for EGR control*1 or air fuel ratio control*2.
      *1: Models with EGR control
      *2: Models without EGR control



    2. The E.F.I. vacuum sensor assembly consists of a silicon chip which utilizes the characteristics of a silicon chip that changes its electrical resistance when pressure is applied to it. The sensor converts the pressure into an electrical signal, and sends it to the ECM in an amplified form.


      W105617E04



  4. Fuel Inlet (Fresh Air Inlet)



    1. The fresh air line inlet is located near the fuel inlet pipe opening. The fresh air from the atmosphere and drain air cleaned by the charcoal canister assembly will go in or out of the system through the passages shown below.


      W100110E09


      Text in Illustration 
      *1
      Fuel Tank Cap
      *2
      Fuel Inlet Pipe
      *a
      To Charcoal Canister Assembly
      -
      -
      V100135
      Fresh Air
      V100136
      Cleaned Drain Air