AIRBAG SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components have the following functions:

    Component
    Function
    Airbag Sensor Assembly
    1. In the event of a frontal collision, the airbag sensor assembly receives signals from either of the front airbag sensors. The airbag sensor assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving a signal from at least one of the front sensors and the safing sensor, the airbag sensor assembly determines whether the horn button assembly (driver airbag), instrument panel passenger airbag without door assembly (front passenger airbag), curtain shield airbag assemblies, and front seat belt pretensioners should be deployed. The airbag sensor assembly also diagnoses system malfunctions.
    2. In the event of a side or rear side collision, the airbag sensor assembly receives signals from the side airbag sensor assemblies or side No. 2 airbag sensor assemblies. The airbag sensor assembly receives the signal via its judgment circuit and also receives another signal from the safing sensor built into the airbag sensor assembly. After receiving a signal from at least one of the side sensors and the safing sensor, the airbag sensor assembly determines whether the front seat airbag assemblies, curtain shield airbag assemblies and front seat belt pretensioner should be deployed. The airbag sensor assembly also diagnoses system malfunctions.
    Horn Button Assembly
    Driver Side Squib
    The airbags are used as supplements to the seat belts to help reduce impact to the occupants.
    Instrument Panel Passenger Airbag without Door Assembly
    Front Passenger Side Squib
    Front Seat Airbag Assembly LH/RH
    Front Side Airbag Squib LH/RH
    Curtain Shield Airbag Assembly LH/RH
    Curtain Shield Squib LH/RH
    Front Airbag Sensor LH/RH
    Based on the deceleration of the vehicle during a frontal collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.
    Side Airbag Sensor Assembly LH/RH
    Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.
    Side No. 2 Airbag Sensor assembly LH/RH
    Front Seat Outer Belt Assembly LH/RH
    Front Pretensioner Squib LHRH
    The front seat outer belt assemblies are used to help reduce impact to the occupants.
    Power Management Control ECU
    1. The power management control ECU receives an airbag deployment signal from the airbag sensor during a frontal, side or rear side collision.
    2. The power management control ECU will shut down the hybrid system power supply by turning the System Main Relays (SMRs) off, in order to ensure safety.
    ECM
    The fuel pump is stopped when an SRS airbag is deployed in a frontal, side, or rear side collision.
    Combination Meter Assembly
    SRS Warning Light
    The SRS warning light turns on to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system.


OPERATING CONDITION


  1. Ignition Condition

    1. Deceleration sensors used for the airbag system are installed on various parts on the vehicle and calculate the deceleration (or acceleration) rate of each part during a collision.

    2. Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag based on the information from each sensor.



    3. Frontal collision signals are produced based on the information from the airbag sensor assembly and front airbag sensors. Frontal collision signals are used to deploy the airbags except the front seat airbag assemblies.


      Y113585E01



    4. The front seat airbag assemblies are deployed and front seat outer belt assemblies are activated based on signals from the side airbag sensor assemblies and airbag sensor assembly.


      Y114562E01



    5. The curtain shield airbag assemblies are deployed based on signals from the side No. 2 airbag sensor assemblies or the side airbag sensor assemblies and the airbag sensor assembly.


      Y113586E03


SYSTEM CONTROL


  1. Airbag for Frontal Collision



    1. There are 2 airbags which deploy in the event of a frontal collision: the horn button assembly, instrument panel passenger airbag without door assembly.


      Y113587E02



  2. Airbag for Side/Side Rear Collision

    1. There are 2 airbags which deploy in the event of a severe side collision: the front seat airbag assembly and curtain shield airbag assembly. These airbags deploy simultaneously. Additionally, at the same time.



    2. For a side collision, if the side airbag sensor assembly detects an impact, it informs the airbag sensor assembly, and the airbag sensor assembly causes the front seat airbag assembly and curtain shield airbag assembly to deploy simultaneously.


      Y114707E01



    3. For a side rear collision, if the side No. 2 airbag sensor assembly detects an impact, it informs the airbag sensor assembly via the side airbag sensor assembly, and the airbag sensor assembly causes the curtain shield airbag assembly to be deployed.


      Y113589E03



  3. Primary Check Illumination Control



    1. After the power switch is turned on (IG), the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If trouble is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed.


      Y112849E02


CONSTRUCTION
  1. Airbag Sensor Assembly

    1. The airbag sensor assembly consists of judgment circuits, a safing sensor, ignition control circuit, backup power source, diagnostic circuit and memory circuit.

      Item
      Outline
      Judgment Circuit
      Judgment circuits are built into the airbag sensor assembly to judge the severity of a collision using the acceleration/deceleration signals from the front airbag sensors, side airbag sensors and side No. 2 airbag sensor assemblies.
      Deceleration Sensor
      A deceleration sensor is built into the airbag sensor assembly. This sensor distorts in the event of a collision. The amount of distortion is based on the deceleration rate of the vehicle during a frontal collision and is converted into an electric signal.
      Ignition Control Circuit
      The ignition control circuit performs calculations based on the signal output from the judgment circuit of the airbag sensor assembly, front airbag sensors, side airbag sensor assemblies and side No. 2 airbag sensor assemblies. If the calculated values are greater than the specified values, the airbags are deployed.
      Safing Sensor
      During a frontal, side or side rear collision, this sensor turns on and outputs an on signal to the airbag sensor assembly if the deceleration rate of the safing sensor is greater than a specified value.
      Backup Power Circuit
      The backup power circuit consists of a power supply capacitor and a DC-DC converter. When the power supply to the airbag sensor assembly is disrupted during a collision, the power supply capacitor discharges and supplies electric power to the system. The DC-DC converter operates as a boosting transformer when the battery voltage falls below a predetermined level.
      Diagnostic Circuit
      The diagnostic circuit constantly monitors for system malfunctions. When a malfunction is detected, it turns on the SRS warning light in the combination meter assembly to inform the driver.
      Memory Circuit
      When a malfunction is detected by the diagnostic circuit, a DTC is stored in memory.



  2. Horn Button Assembly



    1. The horn button assembly contains an initiator and propellant.


      Y111000E01


      Text in Illustration 
      *1
      Bag
      *2
      Inflator
      *3
      Initiator Connector
      -
      -
      *a
      A-A Cross Section
      *b
      Reverse Side



  3. Instrument Panel Passenger Airbag without Door Assembly

    1. The instrument panel passenger airbag without door assembly contains an initiator and propellant.



    2. When the instrument panel passenger airbag without door assembly is deployed, it forms the shapes of 2 bags with a depression in the middle. Immediately after the airbag is deployed, the shapes of 2 bags support the occupant on many planes, including the head and shoulders. Thus, this airbag disperses the load that is applied to the occupant in order to lessen the localized impact that is applied to the occupant immediately upon deployment.


      Y111001E01


      Text in Illustration 
      *1
      Initiator Connector
      *2
      Inflator
      *3
      Bag
      *4
      Depression
      *a
      A-A Cross Section
      -
      -



  4. Front Seat Airbag Assembly



    1. Each front seat airbag assembly is a one-piece design, consisting of an inflator and a bag.


      Y114560E01


      Text in Illustration 
      *1
      Front Seat Airbag Assembly
      *2
      Inflator
      *3
      Bag
      -
      -
      *a
      A-A Cross Section
      *b
      B-B Cross Section



  5. Curtain Shield Airbag Assembly



    1. Each curtain shield airbag assembly is a one-piece design, consisting of an inflator and a bag.


      Y113599E01


      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Inflator
      *3
      Bag
      -
      -
      *a
      A-A Cross Section
      -
      -



  6. Front Airbag Sensor



    1. The front airbag sensors are an electrical type deceleration sensors. As a result of the deceleration of the vehicle during a frontal collision, a distortion is created in the internal element in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.


      Y104921E02



  7. Side Airbag Sensor Assembly and Side No. 2 Airbag Sensor Assembly



    1. A deceleration sensor is enclosed in the side airbag sensor assembly and side No. 2 airbag sensor assembly. As a result of the deceleration of the vehicle during a side or side rear collision, a distortion is created in the internal element in the sensor and converted into an electrical signal.


      Y114706E01


DIAGNOSIS
  1. If the airbag sensor assembly detects a malfunction in the SRS airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.

  2. The airbag sensor assembly outputs the malfunction data and 5-digit Diagnostic Trouble Codes (DTCs) to the intelligent tester.

  3. The 5-digit DTCs can be read after connecting the intelligent tester to the DLC3. For details, refer to the Repair Manual.

  4. If the SRS airbags deploy, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.