LIGHTING SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. High Intensity Discharge (HID) Headlight System

    Component
    Function
    Main Body ECU (Multiplex Network Body ECU)
    Receives the light control signal and transmits a signal to the headlight dimmer relay.
    Headlight Dimmer Switch Assembly
    Light Control Switch
    Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU).
    Headlight Assembly
    Discharge Bulb
    The discharge bulb light shines ahead over a broader area and further forward, increasing the area visible to the driver.
    Light Control ECU
    Transforms battery voltage to a high voltage of up to 30000 V and applies it to the discharge bulbs in order to illuminate them.
    Headlight Dimmer Relay
    Supplies the power to the light control ECUs.

  2. Automatic Headlight Beam Level Control System

    Component
    Function
    Headlight Leveling ECU Assembly
    1. Detects changes of vehicle movement based on the rear height control sensor sub-assembly and vehicle speed signal.
    2. Outputs control signals to the headlight leveling motors based on the detected value.
    3. Provides initial set control and a fail-safe function.
    Headlight Dimmer Switch Assembly
    Light Control Switch
    Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU).
    Headlight Assembly (LH, RH)
    Headlight Leveling Motor (LH, RH)
    1. Based on the signals received from the headlight leveling ECU assembly, each headlight leveling motor moves the projector unit in its headlight to vary its angle.
    2. Each headlight leveling motor uses a stepper motor to precisely regulate the angle of the projector unit.
    Main Body ECU (Multiplex Network Body ECU)
    Receives a light control signal and transmits it to the headlight leveling ECU assembly.
    Rear Height Control Sensor Sub-assembly
    Detects vehicle movement and transmits a signal to the headlight leveling ECU assembly.
    Combination Meter Assembly
    Headlight Leveling Warning Light
    Flashes to inform the driver when the headlight leveling ECU assembly detects malfunctions in this system.

  3. Automatic Light Control System

    Component
    Function
    Main Body ECU (Multiplex Network Body ECU)
    Receives various signals and illuminates the headlights, taillights, parking lights and license plate lights.
    Engine Room Junction Block Assembly
    Supplies power to the high beams.
    Headlight Dimmer Relay
    The headlight dimmer relay supplies power to the low beams.
    Instrument Panel Junction Block Assembly
    - Taillight Relay
    The taillight relay supplies power to the taillights, parking lights and license plate lights.
    Certification ECU (Smart Key ECU Assembly)
    Receives the ignition signal, transmits it to the instrument panel junction block assembly.
    Automatic Light Control Sensor
    Detects the ambient light level.
    Headlight Dimmer Switch Assembly
    Light Control Switch
    Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU).
    Combination Meter Assembly
    Taillight Indicator Light
    Lights up to inform the driver when the taillights turn on.

  4. Light Automatic Turn-off System

    Component
    Function
    Main Body ECU (Multiplex Network Body ECU)
    Receives various signals, and turns off the exterior lights.
    Certification ECU (Smart Key ECU Assembly)
    1. Receives the ignition signal, transmits it to the instrument panel junction block assembly.
    2. Judges and certifies the ID code from the door control receiver.
    Headlight Dimmer Relay
    Shuts down the power to the low beams.
    Engine Room Junction Block Assembly
    Shuts down the power to the high beams and front fog lights.
    Instrument Panel Junction Block Assembly
    - Taillight Relay
    Shuts down the power to the taillights, parking lights and license plate lights.
    Headlight Dimmer Switch Assembly
    Light Control Switch
    Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU).
    Front Door Courtesy Light Switch Assembly (LH, RH)
    Detects whether a door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU).
    Rear Door Courtesy Light Switch Assembly (LH, RH)
    Luggage Compartment Door Courtesy Light Switch Assembly
    Front Door Lock with Motor Assembly (LH, RH)
    - Door Unlock Detection Switch
    Detects whether a door is locked or unlocked and transmits a signal to the main body ECU (multiplex network body ECU).
    Rear Door Lock with Motor Assembly (LH, RH)
    - Door Unlock Detection Switch
    Door Control Receiver
    Receives the ID code from the door control transmitter in the actuation area and transmits it to the main body ECU (multiplex network body ECU) via the certification ECU (smart key ECU assembly).


OPERATING CONDITION
  1. Light Auto Turn-off System

    1. The light auto turn-off system operates as follows:

      Function
      Operation Condition
      Driver Door-linked
      When all of the following conditions are met, the exterior lights automatically turn off:
      1. The power switch is turned on (ACC) or off.
      2. The driver door is opened.


FUNCTION
  1. Automatic Headlight Beam Level Control System

    1. The automatic headlight beam level control system mainly consists of the headlight leveling ECU assembly, rear height control sensor sub-assembly and 2 headlight leveling motors. The headlight leveling ECU assembly controls the system.

    2. The headlight leveling ECU assembly detects the movement of the suspension from the rear height control sensor sub-assembly and the vehicle speed from the combination meter assembly.

    3. The headlight leveling ECU assembly then controls the headlight leveling motor based on this information, in order to change the headlight reflector angle.

    4. When the headlight leveling ECU assembly detects that the vehicle is stopped and the power switch is on (IG), it executes the initial setting of the stepper motors.


CONSTRUCTION
  1. HID Headlight System

    1. Discharge Bulb


      1. Instead of the filament contained in an incandescent bulb, a discharge bulb contains an arc tube, which is filled with xenon gas and metal halide.


        Y104949


FAIL-SAFE
  1. HID Headlight System

    1. The light control ECU executes the fail-safe actions listed below in accordance with the problem that has been detected.

      Problem
      Outline
      Abnormal Input Voltage
      If the voltage that is input to the light control ECU deviates from the normal operating voltage (9 to 16 V), the light control ECU stops illuminating the headlight. It resumes illuminating the headlight once the voltage reverts to the normal operating voltage. However, if the input voltage decreases after the headlights have illuminated, the headlights will remain illuminated until the input voltage becomes insufficient to light the bulbs.
      Abnormal Output (Open Circuit or Short Circuit)
      If an abnormal condition (open or short) occurs in the voltage that is output by the light control ECU, the light control ECU stops illuminating the headlight and will maintain this state until the power is reinstated. Power is reinstated by turning the light control switch from off to on.
      Bulb Open Circuit
      If a bulb is not inserted in its socket, the light control ECU stops generating high voltage until the bulb is inserted correctly and the power is reinstated. Power is reinstated by turning the light control switch from off to on or turning the power switch from off to on (IG).

  2. Automatic Headlight Beam Level Control System

    1. If an abnormal condition such as those listed below is detected, the headlight leveling ECU assembly operates in fail-safe mode.

      1. The headlight leveling ECU assembly illuminates the headlight leveling warning light in the combination meter assembly when an abnormality in the rear height control sensor sub-assembly is detected.

      Trouble Area
      Condition
      Fail-safe Operation
      Rear Height Control Sensor Sub-assembly
      Signal level abnormality
      Holds the beam at the position of the headlight leveling actuator when abnormality is detected.
      Headlight Leveling Motor
      Open or short circuit
      Combination Meter Assembly
      - Vehicle Speed Signal
      Vehicle speed signal pulse abnormality
      Headlight Leveling ECU Assembly
      Voltage abnormality


DIAGNOSIS
  1. Automatic Headlight Beam Level Control System

    1. When the headlight leveling ECU assembly detects malfunctions in the automatic headlight beam level control system, Diagnostic Trouble Codes (DTCs) are stored in memory.

    2. The DTCs can be read using the intelligent tester. For details, refer to the Repair Manual.

  2. Automatic Light Control System

    1. When the main body ECU (multiplex network body ECU) detects malfunctions in the automatic light control system, Diagnostic Trouble Codes (DTCs) are stored in memory.

    2. The DTCs can be read using the intelligent tester. For details, refer to the Repair Manual.