LIGHTING SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
Daytime Running Light System
| Component | Function | |
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and illuminates the daytime running lights via the integration relay. | |
| Engine Room Relay Block and Junction Block Assembly - Integration Relay | Supplies power to the daytime running lights. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU). |
| Certification ECU (Smart Key ECU Assembly) | Receives the ignition signal and transmits it to the instrument panel junction block assembly. | |
| Parking Brake Switch Assembly | Outputs a parking brake operation signal to the main body ECU (multiplex network body ECU). | |
High Intensity Discharge (HID) Headlight System
| Component | Function | |
| Main Body ECU (Multiplex Network Body ECU) | Receives the light control switch signal and transmits a signal to the H-LP relay. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU). |
| Headlight Assembly | Discharge Bulb | Shines ahead over a broader area and further forward, increasing the area visible to the driver. |
| Light Control ECU | Transforms battery voltage to a high voltage of up to 30000 V and applies it to the discharge bulbs in order to illuminate them. | |
| H-LP Relay | Supplies power to the light control ECUs. | |
Automatic Headlight Beam Level Control System
| Component | Function | |
| Headlight Leveling ECU Assembly |
| |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU). |
| Headlight Assembly (LH, RH) | Headlight Leveling Motor (LH, RH) |
|
| Main Body ECU (Multiplex Network Body ECU) | Receives a light control signal and transmits it to the headlight leveling ECU assembly. | |
| Rear Height Control Sensor Sub-assembly | Detects vehicle movement and transmits a signal to the headlight leveling ECU assembly. | |
| Combination Meter Assembly | Multi-information Display | Displays a warning message to inform the driver when the headlight leveling ECU assembly detects a malfunction in this system. |
Automatic Light Control System
| Component | Function | |
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and illuminates the headlights, taillights, clearance lights/daytime running lights and license plate lights. | |
| Engine Room Relay Block and Junction Block Assembly - Integration Relay | Supplies power to the high beams. | |
| H-LP Relay | Supplies power to the low beams. | |
| TAIL Relay | Supplies power to the taillights, parking lights and license plate lights. | |
| Certification ECU (Smart Key ECU Assembly) | Receives the ignition signal and transmits it to the instrument panel junction block assembly. | |
| Automatic Light Control Sensor | Detects the ambient light level. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU). |
| Combination Meter Assembly | Taillight Indicator Light | Lights up to inform the driver when the taillights are on. |
Light Automatic Turn-off System
| Component | Function | |
| Main Body ECU (Multiplex Network Body ECU) | Receives various signals and turns off the exterior lights. | |
| Certification ECU (Smart Key ECU Assembly) |
| |
| H-LP Relay | Shuts down power to the low beams. | |
| Engine Room Relay Block and Junction Block Assembly - Integration Relay | Shuts down power to the high beams and front fog lights. | |
| TAIL Relay | Shuts down power to the taillights, clearance lights/daytime running lights and license plate lights. | |
| Headlight Dimmer Switch Assembly | Light Control Switch | Outputs a light control signal and transmits it to the main body ECU (multiplex network body ECU). |
| Front Door Courtesy Light Switch Assembly (LH, RH) | Detects whether a door is open or closed and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Rear Door Courtesy Light Switch Assembly (LH, RH) | ||
| Luggage Compartment Door Courtesy Light Switch Assembly | ||
| Front Door Lock with Motor Assembly (LH, RH) - Door Unlock Detection Switch | Detects whether a door is locked or unlocked and transmits a signal to the main body ECU (multiplex network body ECU). | |
| Rear Door Lock with Motor Assembly (LH, RH) - Door Unlock Detection Switch | ||
| Door Control Receiver | Receives the ID code from the door control transmitter in the actuation area and transmits it to the main body ECU (multiplex network body ECU) via the certification ECU (smart key ECU assembly). | |
| OPERATING CONDITION |
Daytime Running Light System
The daytime running lights illuminate when all of the following conditions are met:
Light Auto Turn-off System
The light auto turn-off system operates as follows:
| Function | Operation Condition |
| Driver Door-linked | When all of the following conditions are met, the exterior lights automatically turn off:
|
| FUNCTION |
Automatic Headlight Beam Level Control System
The automatic headlight beam level control system mainly consists of the headlight leveling ECU assembly, rear height control sensor sub-assembly and 2 headlight leveling motors. The headlight leveling ECU assembly controls the system.
The headlight leveling ECU assembly detects the movement of the suspension from the rear height control sensor sub-assembly and the vehicle speed from the combination meter assembly.
The headlight leveling ECU assembly then controls the headlight leveling motor based on this information, in order to change the headlight reflector angle.
When the headlight leveling ECU assembly detects that the vehicle is stopped and the power switch is on (IG), it executes the initial setting of the stepper motors.
| CONSTRUCTION |
HID Headlight System
Discharge Bulb

| FAIL-SAFE |
HID Headlight System
The light control ECU executes the fail-safe functions listed below in accordance with the problem that has been detected.
| Problem | Outline |
| Abnormal Input Voltage | If the voltage that is input to the light control ECU deviates from the normal operating voltage (9 to 16 V), the light control ECU stops illuminating the headlight. It resumes illuminating the headlight once the voltage reverts to the normal operating voltage. However, if the input voltage decreases after the headlights have illuminated, the headlights will remain illuminated until the input voltage becomes insufficient to light the bulbs. |
| Abnormal Output (Open Circuit or Short Circuit) | If an abnormal condition (open or short) occurs in the voltage that is output by the light control ECU, the light control ECU stops illuminating the headlight and will maintain this state until power is reinstated. Power is reinstated by turning the light control switch from off to on. |
| Bulb Open Circuit | If a bulb is not inserted in its socket, the light control ECU stops generating high voltage until the bulb is inserted correctly and the power is reinstated. Power is reinstated by turning the light control switch from off to on or turning the power switch from off to on (IG). |
Automatic Headlight Beam Level Control System
If an abnormal condition such as those listed below is detected, the headlight leveling ECU assembly operates in fail-safe mode.
| Malfunctioning Area | Condition | Fail-safe Operation |
| Rear Height Control Sensor Sub-assembly | Signal level abnormality | Holds the beam at the position of the headlight leveling actuator when abnormality is detected. |
| Headlight Leveling Motor | Open or short circuit | |
| Combination Meter Assembly - Vehicle Speed Signal | Vehicle speed signal pulse abnormality | |
| Headlight Leveling ECU Assembly | Voltage abnormality |
| DIAGNOSIS |
Automatic Headlight Beam Level Control System
When the headlight leveling ECU assembly detect a malfunction in the automatic headlight beam level control system, Diagnostic Trouble Codes (DTCs) are stored in memory.
The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.
Automatic Light Control System
When the main body ECU (multiplex network body ECU) detect a malfunction in the automatic light control system, Diagnostic Trouble Codes (DTCs) are stored in memory.
The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.