TOYOTA PARKING ASSIST-SENSOR SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Clearance Warning ECU Assembly
  1. Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors. Output signals are sent to the multi-information display.
  2. Sounds the No. 1 clearance warning buzzer.
No. 1 Ultrasonic Sensor (6)
Detects the distance between the vehicle and an obstacle.
No. 1 Clearance Warning Buzzer
Sounds to inform the driver according to the distance to the obstacle.
Combination Meter Assembly
- Multi-information Display
  1. Displays the location of the obstacle and the approximate distance between the vehicle and the obstacle.
  2. Displays an indication of malfunction or freezing of an No. 1 ultrasonic sensor to inform the driver.
Back Sonar or Clearance Sonar Switch Assembly
Operating this switch allows the operation of toyota parking assist-sensor system to be enabled or disabled.
Air Conditioning Amplifier Assembly
Sends model destination information (information to indicate the market the vehicle was built for - such as Canada) to the clearance warning ECU assembly.
Main Body ECU (Multiplex Network Body ECU)
Sends model destination to the clearance warning ECU assembly.
Power Management Control ECU
Transmits the shift position signals to the clearance warning ECU assembly.

OPERATING CONDITION
  1. The operating condition of each sensor differs according to its installed position as shown in the table below:

    Installation Position
    Operating Condition
    Front Corner
    1. Power switch is on (IG).
    2. System is activated.
    3. Shift lever is in a position other than P.
    4. Vehicle speed is approximately 10 km/h (6 mph) or less.
    Rear Corner
    1. Power switch is (IG).
    2. System is activated.
    3. Shift lever is in R.
    Rear Center
    1. Power switch is (IG).
    2. System is activated.
    3. Shift lever is in R.


CONSTRUCTION


  1. No. 1 Ultrasonic Sensor



    1. The No. 1 ultrasonic sensors consist of a microphone and a circuit portion that transmits and receives ultrasonic waves.


      Y111325E01


      Text in Illustration 
      *1
      Circuit Portion
      *2
      Microphone
      *a
      A-A Cross Section
      -
      -


OPERATION


  1. No. 1 Clearance Warning Buzzer

    1. Depending on the detection distance and the detection area, the sound pattern of the No. 1 clearance warning buzzer will vary.

      Detection Area
      Detection Distance
      (mm (in.))
      Buzzer Sound Pattern
      On
      (msec.)
      Off
      (msec.)
      Front Corner
      Long
      500 +/- 50 to 400 +/- 40 (19.7 +/- 2.0 to 15.7 +/- 1.6)
      150 +/- 15
      150 +/- 15
      Middle
      400 +/- 40 to 300 +/- 30 (15.7 +/- 1.6 to 11.8 +/- 1.2)
      75 +/- 7.5
      75 +/- 7.5
      Short
      300 +/- 30 or less (11.8 +/- 1.2 or less)
      Continuous Sound
      0
      Rear Corner
      Long
      600 +/- 60 to 450 +/- 50 (23.6 +/- 2.4 to 17.7 +/- 2.0)
      150 +/- 15
      150 +/- 15
      Middle
      450 +/- 50 to 300 +/- 30 (17.7 +/- 2.0 to 11.8 +/- 1.2)
      75 +/- 7.5
      75 +/- 7.5
      Short
      300 +/- 30 or less (11.8 +/- 1.2 or less)
      Continuous Sound
      0
      Rear Center
      Longest
      1500 +/- 150 to 600 +/- 60 (59.1 +/- 5.9 to 23.6 +/- 2.4)
      150 +/- 1.5
      650 +/- 65
      Long
      600 +/- 60 to 450 +/- 50 (23.6 +/- 2.4 to 17.7 +/- 2.0)
      150 +/- 1.5
      150 +/- 1.5
      Middle
      450 +/- 50 to 350 +/- 40 (17.7 +/- 2.0 to 13.8 +/- 1.6)
      75 +/- 7.5
      75 +/- 7.5
      Short
      350 +/- 40 or less (13.8 +/- 1.6 or less)
      Continuous Sound
      0



    2. The No. 1 ultrasonic sensors are divided into 2 groups: a front section group (front corners) and a rear section group (rear corners and rear centers). If multiple No. 1 ultrasonic sensors detect obstructions at the same time, the No. 1 clearance warning buzzer sounds as follows, in accordance with the detection distance and detection area of each group:

      Buzzer Sound Pattern ON/OFF Time (msec.) 
      Detection Distance
      Short (*A)
      Middle (*A)
      Long (*A)
      Not detected
      Short (*B)
      Timing 1
      Timing 2
      Timing 2
      Continuous Sound/0
      Middle (*B)
      Timing 2
      75/75
      75/75
      75/75
      Long (*B)
      Timing 2
      75/75
      150/150
      150/150
      Longest (*B)
      Timing 2
      75/75
      150/150
      150/650
      Not detected
      Continuous Sound/0
      75/75
      150/150
      None

      1. *A: Front section
      2. *B: Rear section

      Y102524E04



  2. Multi-information Display

    1. The items displayed by the multi-information display are the location of the obstacle and the approximate distance between the vehicle and the obstacle.



    2. The number of lines shown on the display changes based on the actual distance and the line when the distance is short.


      Y110789E01


      Text in Illustration 
      *1
      Front Corner LH
      *2
      Front Corner RH
      *3
      Rear Corner LH
      *4
      Rear Corner RH
      *5
      Rear Center
      *6
      Distance
      *7
      Longest
      *8
      Long
      *9
      Middle
      *10
      Short
      *11
      Flashes
      -
      -



    3. The items displayed by the multi-information display are warning messages relating to No. 1 ultrasonic sensor malfunction, No. 1 ultrasonic sensor freezing, or presence of dirt on the No. 1 ultrasonic sensor.


      Y110790E01


      Text in Illustration 
      *1
      Malfunctioning
      *2
      Frozen/Dirty



  3. Detection Area

    1. The detection areas of the No. 1 ultrasonic sensor are as shown in the following illustration.



    2. These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.


      Y113164E01


      Text in Illustration (Corner Area:) 
      *a
      Approximately 700 mm (27.6 in.)
      *b
      Approximately 750 mm (29.5 in.)
      *c
      Approximately 500 mm (19.7 in.)
      *d
      Approximately 600 mm (23.6 in.)
      *e
      Approximately 400 mm (15.7 in.)
      *f
      Approximately 400 mm (15.7 in.)
      *g
      Approximately 200 mm (7.9 in.)
      -
      -

      Y113165E01


      Text in Illustration (Rear Center Area:) 
      *a
      Approximately 1800 mm (70.9 in.)
      *b
      Approximately 200 mm (7.9 in.)
      *c
      Approximately 1000 mm (39.4 in.)
      *d
      Approximately 500 mm (19.7 in.)


DIAGNOSIS
  1. If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.