TOYOTA PARKING ASSIST-SENSOR SYSTEM > DETAILS |
| FUNCTION OF MAIN COMPONENTS |
| Component | Function |
| Clearance Warning ECU Assembly |
|
| No. 1 Ultrasonic Sensor (6) | Detects the distance between an vehicle and the obstacle. |
| No. 1 Clearance Warning Buzzer | Sounds to inform the driver according to the distance to the obstacle. |
| Combination Meter Assembly - Multi-information Display |
|
| Back Sonar or Clearance Sonar Switch Assembly | Operating this switch allows the operation of the TOYOTA parking assist-sensor system to be enabled or disabled. |
| Air Conditioning Amplifier Assembly | Sends outside temperature information to the clearance warning ECU assembly to adjust the distance rate from the No. 1 ultrasonic sensors. |
| Main Body ECU (Multiplex Network Body ECU) | Sends model destination (information to indicate the market the vehicle was built for) to the clearance warning ECU assembly. |
| Power Management Control ECU | Transmits the shift position signals to the clearance warning ECU assembly. |
| OPERATING CONDITION |
The operating condition of each sensor differs according to its installed position as shown in the table below:
| Installation Position | Operating Condition |
| Front Corner |
|
| |
| Rear Corner |
|
| Rear Center |
|
| CONSTRUCTION |
No. 1 Ultrasonic Sensor
The No. 1 ultrasonic sensors consist of a microphone and a circuit portion that transmits and receives ultrasonic waves.
The circuit portion is filled with urethane to prevent water from entering.

| *1 | Circuit Portion | *2 | Microphone |
| *a | A-A Cross Section | - | - |
| OPERATION |
No. 1 Clearance Warning Buzzer
Depending on the detection distance and the detection area, the sound pattern of the No. 1 clearance warning buzzer will vary.
| Detection Area | Detection Distance (mm (in.)) | Buzzer Sound Pattern | ||
| On (msec.) | Off (msec.) | |||
| Front Corner | Long | 500 +/- 50 to 400 +/- 40 (19.7 +/- 2.0 to 15.7 +/- 1.6) | 150 +/- 15 | 150 +/- 15 |
| Middle | 400 +/- 40 to 300 +/- 30 (15.7 +/- 1.6 to 11.8 +/- 1.2) | 75 +/- 7.5 | 75 +/- 7.5 | |
| Short | 300 +/- 30 or less (11.8 +/- 1.2 or less) | Continuous Sound | 0 | |
| Rear Corner | Long | 600 +/- 60 to 450 +/- 50 (23.6 +/- 2.4 to 17.7 +/- 2.0) | 150 +/- 15 | 150 +/- 15 |
| Middle | 450 +/- 50 to 300 +/- 30 (17.7 +/- 2.0 to 11.8 +/- 1.2) | 75 +/- 7.5 | 75 +/- 7.5 | |
| Short | 300 +/- 30 or less (11.8 +/- 1.2 or less) | Continuous Sound | 0 | |
| Rear Center | Longest | 1500 +/- 150 to 600 +/- 60 (59.1 +/- 5.9 to 23.6 +/- 2.4) | 150 +/- 1.5 | 650 +/- 65 |
| Long | 600 +/- 60 to 450 +/- 50 (23.6 +/- 2.4 to 17.7 +/- 2.0) | 150 +/- 1.5 | 150 +/- 1.5 | |
| Middle | 450 +/- 50 to 350 +/- 40 (17.7 +/- 2.0 to 13.8 +/- 1.6) | 75 +/- 7.5 | 75 +/- 7.5 | |
| Short | 350 +/- 40 or less (13.8 +/- 1.6 or less) | Continuous Sound | 0 | |
The No. 1 ultrasonic sensors are divided into 2 groups: a front section group (front corners) and a rear section group (rear corners and rear center). If multiple No. 1 ultrasonic sensors detect obstructions at the same time, the No. 1 clearance warning buzzer sounds as follows, in accordance with the detection distance and detection area of each group:
| Detection Distance | Short (*A) | Middle (*A) | Long (*A) | Not detected |
| Short (*B) | Timing 1 | Timing 2 | Timing 2 | Continuous Sound |
| Middle (*B) | Timing 2 | 75/75 | 75/75 | 75/75 |
| Long (*B) | Timing 2 | 75/75 | 150/150 | 150/150 |
| Longest (*B) | Timing 2 | 75/75 | 150/150 | 150/650 |
| Not detected | Continuous Sound | 75/75 | 150/150 | None |

Multi-information Display
The location of an obstacle and the approximate distance between the vehicle and the obstacle are displayed on the multi-information display.
The number of lines shown on the display changes based on the actual distance and flashes when the distance is short.

| *1 | Front Corner LH | *2 | Front Corner RH |
| *3 | Rear Corner LH | *4 | Rear Corner RH |
| *5 | Rear Center | *6 | Distance |
| *7 | Longest | *8 | Long |
| *9 | Middle | *10 | Short |
| *11 | Flashes | - | - |
Screens displaying warning messages relating to a No. 1 ultrasonic sensor malfunction, No. 1 ultrasonic sensor freezing, or presence of foreign matter on the No. 1 ultrasonic sensor, are displayed on the multi-information display.

| *1 | Malfunctioning | *2 | Frozen/Dirty |
Detection Area
The detection areas of the No. 1 ultrasonic sensor are as shown in the following illustration.
These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.

| *a | Approximately 700 mm (27.6 in.) | *b | Approximately 750 mm (29.5 in.) |
| *c | Approximately 500 mm (19.7 in.) | *d | Approximately 600 mm (23.6 in.) |
| *e | Approximately 400 mm (15.7 in.) | *f | Approximately 200 mm (7.9 in.) |

| *a | Approximately 1800 mm (70.9 in.) | *b | Approximately 200 mm (7.9 in.) |
| *c | Approximately 1000 mm (39.4 in.) | *d | Approximately 500 mm (19.7 in.) |
| DIAGNOSIS |
If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.