Home › Brake › PARKING BRAKE › PARKING BRAKE ASSEMBLY

PARKING BRAKE ASSEMBLY > DISASSEMBLY

for Preparation Click here


NOTICE:
  1. When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
  2. While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISABLE BRAKE CONTROL (for LHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C239901
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)
(Click here)


4. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C243048
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C245589
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C243049
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



5. DISABLE BRAKE CONTROL (for RHD)
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C242738
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



6. REMOVE REAR WHEEL


7. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C083014
  1. Remove the bolt and separate the rear flexible hose from the rear shock absorber assembly.

  1. Remove the 2 bolts, and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging down by the rear flexible hose.



8. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG


9. REMOVE REAR DISC


    C238505E01
  1. Put matchmarks on the rear disc and the rear axle hub.
    Text in Illustration 
    *a
    Matchmark



    C201774
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, use a screwdriver to turn the shoe adjuster as shown in the illustration in order to contract the parking brake shoes.



10. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)


  1. for Rear Side:



      C239422
    1. Remove the parking brake shoe return tension spring.



  1. for Front Side:



      C239423
    1. Remove the parking brake shoe return tension spring.



11. REMOVE PARKING BRAKE SHOE STRUT


    C239424
  1. Pull the No. 1 parking brake shoe assembly towards the front of the vehicle by hand as shown in the illustration.



    C239425
  1. Remove the parking brake shoe strut.



12. REMOVE PARKING BRAKE SHOE STRUT COMPRESSION SPRING


    C240876
  1. Remove the parking brake shoe strut compression spring.



13. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    C239426E01
  1. Release the claw of the parking brake shoe hold down spring cup and separate the No. 1 parking brake shoe assembly.



14. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY


    C239427E01
  1. Release the claw of the parking brake shoe hold down spring cup and separate the No. 2 parking brake shoe assembly.



15. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    C239428
  1. Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and pull downward to separate them from the parking brake plate.



    C239429
  1. Remove the parking brake shoe adjusting screw set.



16. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    C239430
  1. Remove the No. 1 parking brake shoe assembly.



17. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    C239431
  1. Remove the parking brake shoe return tension spring.



18. SEPARATE PARKING BRAKE SHOE LEVER


    C239432
  1. Using needle-nose pliers, separate the parking brake shoe lever from the No. 3 parking brake cable assembly.



19. REMOVE PARKING BRAKE SHOE LEVER


    C239433
  1. Using a screwdriver, remove the parking brake shoe type C washer, parking brake shoe shim and the parking brake shoe lever.

    HINT:
    Parking brake shoe shims are provided when necessary to adjust the clearance between the parking brake shoe lever and parking brake shoe type C washer. Some vehicles may not be equipped with shims.



20. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN


  1. for Front Side:



      C240101
    1. Remove the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.



  1. for Rear Side:



      C240102
    1. Remove the 2 parking brake shoe hold down spring cups, parking brake shoe hold down spring and parking brake shoe hold down spring pin.



21. REMOVE PARKING BRAKE SHOE GUIDE PLATE


    C240103
  1. Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.