WINDSHIELD GLASS > REMOVAL |
| 1. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and front wiper arm and blade assembly LH.
| 2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and front wiper arm and blade assembly RH.
| 3. REMOVE FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Disengage the 2 clips and 3 guides, and remove the front fender to cowl side seal LH as shown in the illustration.
| 4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH |
| 5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Disengage the 6 claws and guide as shown in the illustration.

Disengage the 8 guides and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.

| 6. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER |
![]() |
Disengage the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration.
![]() |
Disengage the 6 claws and remove the inner rear view mirror stay holder cover.
| 7. REMOVE INNER REAR VIEW MIRROR ASSEMBLY |
![]() |
Disconnect the connector.
Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror assembly.
| 8. REMOVE RAIN SENSOR COVER |
![]() |
Disengage the 2 claws and remove the rain sensor cover as shown in the illustration.
| 9. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 10. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.
| *1 | Front Pillar Garnish Clip |
![]() |
While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.
Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.
![]() |
Protect the curtain shield airbag assembly.
| *1 | Adhesive Tape |
| *2 | Protective Cover |
| *3 | Curtain Shield Airbag Assembly |
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
| 11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Disconnect the front door opening trim weatherstrip RH.
| 12. REMOVE FRONT PILLAR GARNISH RH |
| 13. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof) |
![]() |
Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the roof console box assembly.
| 14. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof) |
![]() |
Using a moulding remover, disengage the 4 clips.
Disconnect the connector and remove the roof console box assembly.
| 15. REMOVE SPOT LIGHT ASSEMBLY |
![]() |
Using a moulding remover, disengage the 4 claws.
| *a | Front |
Disconnect the connector and remove the spot light assembly.
| 16. REMOVE ASSIST GRIP SUB-ASSEMBLY |
![]() |
Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
| *1 | Protective Tape |
![]() |
Disengage the 2 clips and remove the assist grip sub-assembly.
Remove the 2 clips from the vehicle body.
| 17. REMOVE REAR ASSIST GRIP ASSEMBLY LH |
![]() |
Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
| *1 | Protective Tape |
![]() |
Disengage the 2 clips and remove the rear assist grip assembly LH.
Remove the 2 clips from the vehicle body.
| 18. REMOVE REAR ASSIST GRIP ASSEMBLY RH |
| 19. REMOVE VISOR BRACKET COVER (for LH Side) |
![]() |
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
| 20. REMOVE VISOR ASSEMBLY LH |
![]() |
Remove the 2 screws and visor assembly LH.
| 21. REMOVE VISOR BRACKET COVER (for RH Side) |
| 22. REMOVE VISOR ASSEMBLY RH |
| 23. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
| 24. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
Remove the sliding roof opening trim moulding.
| 25. REMOVE ROOF HEADLINING ASSEMBLY |
Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.
| 26. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY |
![]() |
Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.
| *1 | Protective Tape |
![]() |
Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.
| *1 | Wooden Block |
| *2 | Plastic Sheet |
| *3 | Stopper |
| *4 | Piano Wire |
| *5 | Windshield Glass Retainer |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.
![]() |
Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.
| *1 | Matchmark |
Disconnect the windshield glass stoppers.

| *A | 1-piece Type | *B | 2-pieceType |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
| *3 | Windshield Glass Retainer | - | - |
Using suction cups, remove the windshield glass sub-assembly.
| 27. REMOVE WINDSHIELD GLASS ADHESIVE DAM |
When reusing the windshield glass:
![]() |
Using a scraper, remove the windshield glass adhesive dam.
| *A | Back Side |
| 28. REMOVE WINDSHIELD OUTSIDE MOULDING |
When reusing the windshield glass:
![]() |
Using a scraper, remove the windshield outside moulding.
| *A | Back Side |
| 29. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type) |
When reusing the windshield glass:
![]() |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
| *A | Back Side |
| 30. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
When reusing the windshield glass:
![]() |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
| *A | Back Side |
| 31. REMOVE WINDSHIELD GLASS RETAINER |
When reusing the windshield glass:
![]() |
Remove the 2 windshield glass retainers.
| *A | Back Side |
| 32. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type) |
![]() |
Remove the 2 No. 1 windshield glass stoppers.
| 33. CLEAN WINDSHIELD GLASS |
When reusing the windshield glass:
![]() |
Using a scraper, remove any adhesive dam and adhesive residue from the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
| 34. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surfaces of the vehicle body.
| *1 | Adhesive |
| *2 | Body |
Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.
Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.