Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS

BACK WINDOW GLASS > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)
  1. Using a brush or sponge, coat the application area of 2 new No. 2 back window glass stoppers with Primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B280237E02
  1. Install the 2 new No. 2 back window glass stoppers onto the back window glass as shown in the illustration.
    Text in Illustration 
    *A
    Back Side
    *1
    Ceramic Notch
    *a
    Back Window Glass Edge Side

    Standard Dimension:
    Area
    Dimension
    a
    14.2 to 15.2 mm (0.559 to 0.598 in.)

    HINT:
    Only 2-piece type No. 2 back window glass stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



2. INSTALL NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    B280236
  1. Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.

    HINT:
    Only 2-piece type back window glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if a 1-piece type was originally installed.



3. INSTALL BACK WINDOW OUTSIDE MOULDING
  1. Using a brush or sponge, coat the application area of a new back window outside moulding with Primer G.

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Throw away any leftover primer G.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



    B280238E01
  1. Install the new back window outside moulding onto the back window glass as shown in the illustration.
    Text in Illustration 
    *A
    Back Side

    Standard Dimension:
    Area
    Dimension
    a
    7.4 mm (0.291 in.)



4. INSTALL BACK WINDOW GLASS ADHESIVE DAM
  1. Using a brush or sponge, coat the application area of a new back window glass adhesive dam with Primer G.

    NOTICE:
    1. Allow the primer G coating to dry for 3 minutes or more.
    2. Do not apply too much primer G.



  1. Install the new back window adhesive dam, applying double-sided tape all the way around the glass except where the dam is installed as shown in the illustration.


    B294620E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Ceramic Notch
    *2
    Back Window Glass Adhesive Dam

    Standard Dimension:

    Area
    Dimension
    a
    7.4 mm (0.291 in.)

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



5. INSTALL BACK WINDOW GLASS SUB-ASSEMBLY


    B280230E01
  1. Position the back window glass.
    Text in Illustration 
    *1
    Matchmark

    1. Using suction cups, place the back window glass in the correct position.

    2. Check that the whole contact surface of the back window glass rim is perfectly even.

    3. Align the matchmarks on the back window glass and vehicle body.

      NOTICE:
      Check that the back window glass stoppers are attached to the vehicle body correctly.

    4. Remove the back window glass.



  1. Using a brush, coat the installation surface on the vehicle body with Primer M.


    B280240E01


    Text in Illustration 
    *1
    Brush
    *2
    Primer M
    *3
    Adhesive
    -
    -
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Do not coat the adhesive with Primer M.
    2. Do not apply too much primer M.
    3. Allow the primer M coating to dry for 3 minutes or more.
    4. Do not keep any of the opened Primer M for later use.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



  1. Using a brush or sponge, coat the adhesive application area with Primer G.


    B290090E01


    Text in Illustration 
    *A
    Back Side
    -
    -
    *1
    Adhesive Center Line
    *2
    Ceramic Notch
    *3
    Primer G
    -
    -

    Standard Dimension:

    Area
    Dimension
    a
    16.0 mm (0.630 in.) or more
    b
    8.3 mm (0.327 in.) or more
    c
    14.2 mm (0.559 in.) or more
    d
    8.0 mm (0.315 in.) or more
    e
    14.0 mm (0.551 in.) or more
    f
    8.0 mm (0.315 in.) or more

    NOTICE:
    1. Do not apply too much primer G.
    2. Allow the primer G coating to dry for 3 minutes or more.
    3. Do not keep any of the opened Primer G for later use.

    HINT:
    If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent




      B214800E07
    1. Cut off the tip of the cartridge nozzle as shown in the illustration.
      Text in Illustration 
      *1
      Nozzle

      Standard Dimension:
      Area
      Dimension
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour and 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back window glass as shown in the illustration.


      B280242E01


      Text in Illustration 
      *A
      Back Side
      -
      -
      *1
      Adhesive Center Line
      *2
      Ceramic Notch
      *3
      Adhesive
      -
      -

      Standard Dimension:

      Area
      Dimension
      a
      6.5 mm (0.256 in.)
      b
      8.0 mm (0.315 in.)
      c
      10.0 mm (0.394 in.)
      d
      10.0 mm (0.394 in.)
      e
      16.5 mm (0.650 in.)



  1. Install the back window glass sub-assembly.



      B280230E01
    1. Using suction cups, position the back window glass so that the matchmarks are aligned, and press it in gently along the rim.
      Text in Illustration 
      *1
      Matchmark

      NOTICE:
      1. Check that the back window glass stoppers are attached to the vehicle body correctly.
      2. Check the clearance between the vehicle body and back window glass.

    2. Lightly press the front surface of the back window glass to ensure a close fit.

      HINT:
      Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.

    3. Using a scraper, remove any excess or protruding adhesive.

    4. Hold the back window glass using protective tape until the applied adhesive becomes hard.

      NOTICE:
      Do not drive the vehicle for the time described in the table below.

      Minimum Time:
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour and 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours

  1. Connect each connector.



6. INSPECT FOR LEAKS AND REPAIR
  1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.

  1. If water leaks into the cabin, allow the water to dry and add adhesive.

  1. Remove the protective tape.



7. INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Pass the center stop light connector through the No. 2 package tray trim panel assembly.

  1. Engage the 5 guides and 3 clips, and install the No. 2 package tray trim panel assembly.



8. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.



    B381283
  1. Engage the guide and 3 clips to install the package tray trim panel assembly.



9. INSTALL REAR SEAT SHOULDER BELT COVER


    B271098
  1. Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.



10. INSTALL CENTER STOP LIGHT SET
  1. Connect the connector.

  1. Temporarily install the center stop light set.



    E226679E01
  1. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.



11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    B279455E03
  1. Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.
    2. Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.



12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
  1. Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



13. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B279441E05
  1. Connect the floor anchor of the rear seat outer belt assembly with the bolt.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.



14. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B279443E02
  1. Connect the floor anchor of the rear seat outer belt assembly with the bolt.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.



15. INSTALL ROOF HEADLINING ASSEMBLY
(Click here)