Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS

BACK WINDOW GLASS > REMOVAL

for Preparation Click here



1. REMOVE ROOF HEADLINING ASSEMBLY
(Click here)


2. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B279440
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



3. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B279442
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



4. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    B298603
  1. Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.



5. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    B279454
  1. Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.



6. REMOVE CENTER STOP LIGHT SET


    E226678E01
  1. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.



    E231297
  1. Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

    HINT:
    This makes it easier to disconnect the connector.

  1. Disconnect the connector and remove the center stop light set.



7. REMOVE REAR SEAT SHOULDER BELT COVER


    B271099
  1. Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.



8. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    B293942E01
  1. Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the tips of pliers before use.

  1. Disengage the 5 guides.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.



9. REMOVE BACK WINDOW GLASS SUB-ASSEMBLY
  1. Disconnect each connector.



    B280229E01
  1. Apply protective tape to the area around the installation position of the back window glass on the vehicle body to prevent it from being scratched.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Apply protective tape to the vehicle body to prevent it from being scratched.



    B280231E02
  1. Pass a piano wire between the vehicle body and glass from the interior.
    Text in Illustration 
    *1
    Stopper
    *2
    Window Defogger Connector
    *3
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects.

  1. Cut off the adhesive by pulling the piano wire around the back window glass.

    NOTICE:
    When separating the back window glass, take care not to damage the paint or interior and exterior ornaments.



    B280230E01
  1. Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks are not needed to be placed if the back window glass will not be reused.



  1. Disconnect the back window glass stoppers.


    B280233E01


    Text in Illustration 
    *A
    1-piece type
    *B
    2-piece type
    *1
    No. 1 Back Window Glass Stopper
    *2
    No. 2 Back Window Glass Stopper

    NOTICE:
    1. There are No. 1 and No. 2 stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.
    2. To prevent the back window glass from falling when performing this operation, be sure to hold the back window glass using suction cups.

    HINT:
    Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.

  1. Using suction cups, remove the back window glass sub-assembly.

    NOTICE:
    1. Be careful not to drop the back window glass.
    2. Leave as much adhesive on the vehicle body as possible when removing the back window glass.



10. REMOVE BACK WINDOW GLASS ADHESIVE DAM


  1. When reusing the back window glass:



      B280251E01
    1. Using a scraper, remove the back window glass adhesive dam.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the back window glass adhesive dam with a new one.



11. REMOVE BACK WINDOW OUTSIDE MOULDING


  1. When reusing the back window glass:



      B280234E01
    1. Using a scraper, remove the back window outside moulding.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the back window outside moulding with a new one.



12. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)


  1. When reusing the back window glass:



      B280235E01
    1. Using a scraper, remove the 2 No. 1 back window glass stoppers.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the No. 1 back window glass stoppers with new ones.



13. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)


  1. When reusing the back window glass:



      B280235E01
    1. Using a scraper, remove the 2 No. 2 back window glass stoppers.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the back window glass.
      2. Be sure to replace the No. 2 back window glass stoppers with new ones.



14. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    B280236
  1. Remove the 2 No. 1 back window glass stoppers.

    NOTICE:
    Be sure to replace the No. 1 back window glass stoppers with new ones.



15. CLEAN BACK WINDOW GLASS
  1. Using a scraper, remove any adhesive dam and adhesive residue from the back window glass.

    NOTICE:
    Be careful not to damage the back window glass.



    B187131
  1. Clean the outer circumference of the back window glass with a non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using new glass, clean it with a non-residue solvent.



16. CLEAN VEHICLE BODY


    B149737E07
  1. Clean and shape the contact surface of the vehicle body.
    Text in Illustration 
    *1
    Adhesive
    *2
    Body

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.