Home › Brake › BRAKE (FRONT) › FRONT BRAKE

FRONT BRAKE > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The following procedure is for the LH side.



1. INSTALL FRONT DISC


    C238490E01
  1. Align the matchmarks of the front disc and front axle hub, and install the front disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



2. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT
  1. Secure the front disc brake cylinder mounting in a vise.



    C239550
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.



    C238493
  1. Using a socket wrench (19 mm) and a hammer, install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.



3. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING


    C238488
  1. Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1090 kgf*cm , 79 ft.*lbf }



4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING


    C211757
  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease

  1. Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.



5. INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN


    C211758
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 2 disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease



    C238487
  1. Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.

  1. Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.



6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


    C211759
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.
    Text in Illustration 
    V100155
    Lithium Soap Base Glycol Grease



    C238486
  1. Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.

  1. Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.



7. INSTALL FRONT DISC BRAKE FITTING KIT


    C238494E01
  1. Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.
    Text in Illustration 
    *1
    Front No. 1 Disc Brake Pad Support Plate
    *2
    Front No. 2 Disc Brake Pad Support Plate

    NOTICE:
    Be sure to install each front disc brake pad support plate in the correct position and direction.



8. INSTALL FRONT ANTI-SQUEAL SHIM KIT


    C239560
  1. Install the front disc brake pad wear indicator plate to each front disc brake pad.

    NOTICE:
    Install each front disc brake pad wear indicator plate in the correct position and direction.



    C239549
  1. Apply disc brake grease to the inside of each front disc brake anti-squeal shim as shown in the illustration.
    Text in Illustration 
    V100155
    Disc Brake Grease



    C239559
  1. Install the front disc brake anti-squeal shim to each front disc brake pad.

    NOTICE:
    1. Install the front disc brake anti-squeal shims in the correct positions and directions.
    2. Disc brake grease can seep out slightly from the area where the front disc brake anti-squeal shim is installed.
    3. Make sure that disc brake grease is not applied onto the lining surface.



9. INSTALL FRONT DISC BRAKE PAD KIT
  1. Install the 2 front disc brake pads with front anti-squeal shim kit to the front disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



    C238483
  1. Install the 2 anti-squeal springs to the front disc brake pads.

    NOTICE:
    1. When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.
    2. Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.



10. INSTALL DISC BRAKE CYLINDER ASSEMBLY


    C239568E01
  1. Hold the front disc brake cylinder slide pin, and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



11. CONNECT FRONT FLEXIBLE HOSE


    C238481E01
  1. Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.
    Text in Illustration 
    *a
    Lock Hole

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.



12. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
  1. Connect the cable to the negative (-) auxiliary battery terminal .

  1. Perform the following procedure if air bleeding is not necessary:

    1. Connect the reservoir level switch connector.

    2. Clear the DTCs (Click here).



13. BLEED BRAKE LINE


  1. Bleed brake line.



      C239900
    1. Remove the brake master cylinder reservoir filler cap assembly.

    2. Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

    4. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Air Bleeding.

    5. Select "Usual air bleeding" on the intelligent tester display, and bleed air from the brake fluid following the instructions on the intelligent tester.

    6. After air bleeding, tighten each bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Clear the DTCs (Click here).

    8. Turn the intelligent tester off and turn the power switch off.

  1. Inspect for brake fluid leaks.

  1. Install the brake master cylinder reservoir filler cap.



14. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
  1. Install the front outer cowl top panel sub-assembly with the 10 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.

  1. Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.



15. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)



16. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }