FRONT BRAKE > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD) |
| 3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 4. DISABLE BRAKE CONTROL (for LHD) |
Wait at least 2 minutes after turning the power switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 5. DISABLE BRAKE CONTROL (for RHD) |
Wait at least 2 minutes after turning the power switch off.
![]() |
Disconnect the reservoir level switch connector with the parking brake applied.
Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).
Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.
Check that the brake pedal can not be further depressed.
Release the parking brake.
| 6. REMOVE FRONT WHEEL |
| 7. DRAIN BRAKE FLUID |
| 8. SEPARATE FRONT FLEXIBLE HOSE |
![]() |
Remove the union bolt and gasket, and separate the front flexible hose from the disc brake cylinder assembly.
| 9. REMOVE DISC BRAKE CYLINDER ASSEMBLY |
![]() |
Hold the front disc brake cylinder slide pin, and remove the 2 bolts and disc brake cylinder assembly.
| *a | Hold |
| *b | Turn |
| 10. REMOVE FRONT DISC BRAKE PAD KIT |
![]() |
Remove the 2 anti-squeal springs from the front disc brake pads.
![]() |
Remove the 2 front disc brake pads with front anti-squeal shim kit from the front disc brake cylinder mounting.
| 11. REMOVE FRONT ANTI-SQUEAL SHIM KIT |
![]() |
Remove the front disc brake anti-squeal shim from each front disc brake pad.
![]() |
Remove the front disc brake pad wear indicator plate from each front disc brake pad.
| 12. REMOVE FRONT DISC BRAKE FITTING KIT |
![]() |
Remove the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates from the front disc brake cylinder mounting.
| *1 | Front No. 1 Disc Brake Pad Support Plate |
| *2 | Front No. 2 Disc Brake Pad Support Plate |
| 13. REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN |
![]() |
Remove the front disc brake cylinder slide pin from the front disc brake cylinder mounting.
| 14. REMOVE FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN |
![]() |
Remove the front No. 2 disc brake cylinder slide pin from the front disc brake cylinder mounting.
| 15. REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSHING |
![]() |
Using a screwdriver with its tip wrapped with vinyl tape, remove the front disc brake cylinder slide bushing from the front No. 2 disc brake cylinder slide pin.
| *1 | Vinyl Tape |
| 16. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING |
![]() |
Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.
| 17. REMOVE FRONT DISC BRAKE BUSHING DUST BOOT |
![]() |
Secure the front disc brake cylinder mounting in a vise.
Using a screwdriver and a plastic hammer, remove the 2 front disc brake bushing dust boots.
| 18. REMOVE FRONT DISC |
![]() |
Put matchmarks on the front disc and the front axle hub.
| *a | Matchmark |
Remove the front disc.