Terminal No. (Symbol)
| Wiring Color
| Terminal Description
| Condition
| Specified Condition
|
A25-1 (BATT) - E28-16 (E1)
| GR - BR
| Auxiliary battery (for measuring auxiliary battery voltage and for ECM memory)
| Power switch off
| 11 to 16 V
|
A25-2 (+B) - E28-16 (E1)
| P - BR
| Power source of ECM
| Power switch on (IG)
| 11 to 14 V
|
A25-3 (+B2) - E28-16 (E1)
| LG - BR
| Power source of ECM
| Power switch on (IG)
| 11 to 14 V
|
E28-29 (+BM) - E28-16 (E1)
| B - BR
| Power source of throttle actuator
| Power switch off
| 11 to 16 V
|
A25-37 (IGSW) - E28-16 (E1)
| V - BR
| Power switch on (IG) signal
| Power switch on (IG)
| 11 to 14 V
|
E28-74 (OC1+) - E28-75 (OC1-)
| W - B
| Camshaft timing oil control valve assembly operation signal
| Idling
| Pulse generation (See waveform 1)
|
A25-46 (MREL) - E28-16 (E1)
| BE - BR
| EFI MAIN relay operation signal
| Power switch on (IG)
| 11 to 14 V
|
E28-91 (VG) - E28-92 (E2G)
| L - R
| Mass air flow meter sub-assembly signal
| Idling, shift lever in P, A/C switch off
| 0.5 to 3.0 V
|
E28-93 (THA) - E28-94 (ETHA)
| P - Y
| Intake air temperature sensor signal
| Idling, intake air temperature 20°C (68°F)
| 0.5 to 3.4 V
|
E28-95 (THW) - E28-96 (ETHW)
| B - P
| Engine coolant temperature sensor signal
| Idling, engine coolant temperature 80°C (176°F)
| 0.2 to 1.0 V
|
E28-125 (VCTA) - E28-126 (ETA)
| B - R
| Power source of throttle position sensor (specific voltage)
| Power switch on (IG)
| 4.5 to 5.5 V
|
E28-127 (VTA1) - E28-126 (ETA)
| Y - R
| Throttle position sensor signal (for engine control)
| Accelerator pedal fully released
| 0.5 to 1.1 V
|
E28-128 (VTA2) - E28-126 (ETA)
| W - R
| Throttle position sensor signal (for sensor malfunction detection)
| Accelerator pedal fully released
| 2.1 to 3.1 V
|
E28-23 (HA1A) - E28-53 (E04)
| G - W-B
| Air fuel ratio sensor heater operation signal
| Idling
| Pulse generation (See waveform 2)
|
Power switch on (IG)
| 11 to 14 V
|
E28-133 (A1A+) - E28-16 (E1)
| L - BR
| Air fuel ratio sensor signal
| Power switch on (IG)
| 3.3 V*
|
E28-134 (A1A-) - E28-16 (E1)
| P - BR
| Air fuel ratio sensor signal
| Power switch on (IG)
| 2.9 V*
|
E28-24 (HT1B) - E28-53 (E04)
| Y - WB
| Heated oxygen sensor heater operation signal
| Idling
| Below 3.0 V
|
Power switch on (IG)
| 11 to 14 V
|
E28-100 (OX1B) - E28-132 (EX1B)
| W - R
| Heated oxygen sensor signal
| Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
| Pulse generation (See waveform 3)
|
E28-20 (#10) - E28-50 (E01)
| B - W-B
| No. 1 fuel injector assembly signal
| Power switch on (IG)
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 4)
|
E28-17 (#20) - E28-50 (E01)
| R - W-B
| No. 2 fuel injector assembly signal
| Power switch on (IG)
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 4)
|
E28-18 (#30) - E28-50 (E01)
| Y - W-B
| No. 3 fuel injector assembly signal
| Power switch on (IG)
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 4)
|
E28-19 (#40) - E28-50 (E01)
| L - W-B
| No. 4 fuel injector assembly signal
| Power switch on (IG)
| 11 to 14 V
|
Idling
| Pulse generation (See waveform 4)
|
E28-123 (KNK1) - E28-124 (EKNK)
| R - G
| Knock control sensor signal
| Engine speed maintained at 2500 rpm after warming up engine
| Pulse generation (See waveform 5)
|
E28-113 (VCV1) - E28-16 (E1)
| B - BR
| Power source of camshaft position sensor (specific voltage)
| Power switch on (IG)
| 4.5 to 5.5 V
|
E28-82 (VV1+) - E28-114 (VV1-)
| V - L
| Camshaft position sensor signal
| Idling
| Pulse generation (See waveform 6)
|
A25-60 (G2O) - E28-16 (E1)
| B - BR
| Camshaft revolution signal
| Idling
| Pulse generation (See waveform 7)
|
E28-76 (NE+) - E28-109 (NE-)
| B - W
| Crankshaft position sensor signal
| Idling
| Pulse generation (See waveform 8)
|
E28-57 (IGT1) - E28-16 (E1)
| Y - BR
| No. 1 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E28-56 (IGT2) - E28-16 (E1)
| R - BR
| No. 2 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E28-55 (IGT3) - E28-16 (E1)
| G - BR
| No. 3 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E28-54 (IGT4) - E28-16 (E1)
| L - BR
| No. 4 ignition coil assembly (ignition signal)
| Idling
| Pulse generation (See waveform 9)
|
E28-51 (IGF1) - E28-16 (E1)
| W - BR
| Ignition coil assembly (ignition confirmation signal)
| Power switch on (IG)
| 4.5 to 5.5 V
|
Idling
| Pulse generation (See waveform 9)
|
E28-68 (PRG) - E28-50 (E01)
| W - W-B
| Purge VSV operation signal
| Power switch on (IG)
| 11 to 14 V
|
Idling, under purge control
| Pulse generation (See waveform 10)
|
E28-60 (M+) - E28-58 (ME01)
| W - W-B
| Throttle actuator operation signal (positive terminal)
| Idling with warm engine
| Pulse generation (See waveform 11)
|
E28-30 (M-) - E28-58 (ME01)
| B - W-B
| Throttle actuator operation signal (negative terminal)
| Idling with warm engine
| Pulse generation (See waveform 12)
|
A25-21 (FC) - E28-50 (E01)
| R - W-B
| Fuel pump control
| Power switch on (IG)
| 11 to 14 V
|
A25-30 (W) - E28-16 (E1)
| Y - BR
| Malfunction Indicator Lamp (MIL) operation signal
| Power switch on (IG) (MIL goes on)
| Below 3.0 V
|
Idling
| 11 to 14 V
|
A25-23 (TC) - E28-16 (E1)
| P - BR
| Terminal TC of DLC3
| Power switch on (IG)
| 11 to 14 V
|
A25-31 (TACH) - E28-16 (E1)
| L - BR
| Engine speed signal
| Idling
| Pulse generation (See waveform 13)
|
A25-13 (CANH) - E28-16 (E1)
| B - BR
| CAN communication line
| Power switch on (IG)
| Pulse generation (See waveform 14)
|
A25-26 (CANL) - E28-16 (E1)
| W - BR
| CAN communication line
| Power switch on (IG)
| Pulse generation (See waveform 15)
|
A25-12 (CANP) - E28-16 (E1)
| B - BR
| CAN communication line
| Power switch on (IG)
| Pulse generation (See waveform 14)
|
A25-25 (CANN) - E28-16 (E1)
| W -BR
| CAN communication line
| Power switch on (IG)
| Pulse generation (See waveform 15)
|
A25-28 (WPI) - E28-16 (E1)
| BE -BR
| Engine water pump assembly signal
| Idling with warm engine
| Pulse generation (See waveform 16)
|
A25-29 (WPO) - E28-16 (E1)
| LG - BR
| Engine water pump assembly signal
| Idling with warm engine
| Pulse generation (See waveform 17)
|
E28-78 (VCPM) - E28-80 (EPIM)
| B - V
| Power source of manifold absolute pressure sensor
| Power switch on (IG)
| 4.75 to 5.25 V
|
E28-79 (PIM) - E28-80 (EPIM)
| G - V
| Manifold absolute pressure sensor signal
| Power switch on (IG)
| 3.0 to 5.0 V
|
A25-44 (RFC) - E28-16 (E1)
| G - BR
| Cooling fan control
| Power switch on (IG), A/C switch on (max cool)
| Pulse generation (See waveform 18)
|
A25-14 (EC) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E28-16 (E1) - Body ground
| BR- -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E28-50 (E01) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E28-49 (E02) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E28-53 (E04) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E28-58 (ME01) - Body ground
| W-B - -
| Earth (ground) circuit of ECM
| Always
| Below 1 Ω
|
E28-59 (GE01) - Body ground
| R - -
| Shielded earth (ground) circuit of throttle actuator
| Always
| Below 1 Ω
|