Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B282096E08

  1. Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3D-31 (BECU) - Body ground
    V - Body ground
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    3E-1*1 - Body ground
    W - Body ground
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    3F-1*2 - Body ground
    B - Body ground
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-7 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.



  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3D-7 - Body ground
    L - Body ground
    Parking light RH drive output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-8 - Body ground
    W - Body ground
    Parking light LH drive output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-9 - Body ground
    P - Body ground
    Taillight relay drive signal output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-12 (HRLY) - Body ground
    P - Body ground
    Headlight relay drive output
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    11 to 14 V
    3D-35 (RFGO)*3 - Body ground
    B - Body ground
    Rear fog light drive output
    Light control switch in tail or head position, rear fog light switch on
    Below 1 V
    Light control switch in tail or head position, rear fog light switch off
    11 to 14 V
    3D-38 (FFGO) - Body ground
    P - Body ground
    Front fog light drive output
    Light control switch in tail or head position, front fog light switch on
    Below 1 V
    Light control switch in tail or head position, front fog light switch off
    11 to 14 V
    3D-39 (DIM) - Body ground
    W - Body ground
    High beam headlight drive output
    Dimmer switch in high or high flash position
    Below 1 V
    Dimmer switch in low position
    11 to 14 V
    3C-5 - Body ground
    P - Body ground
    Taillight relay drive signal output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    I13-5 (HU) - Body ground
    LG - Body ground
    Dimmer switch high position signal input
    Dimmer switch in high position
    Below 1 V
    Dimmer switch not in high position
    Pulse generation
    I13-8 (HF) - Body ground
    R - Body ground
    Dimmer switch high flash position signal input
    Dimmer switch in high flash position
    Below 1 V
    Dimmer switch not in high flash position
    Pulse generation
    I13-20 (CLTB) - I13-22 (CLTE)
    B - P
    Automatic light control sensor power supply output
    Power switch off
    Below 1 V
    Power switch on (IG), light control switch in AUTO position
    11 to 14 V
    I13-21 (CLTS) - Body ground
    G - Body ground
    Automatic light control sensor signal input
    Power switch off
    Below 1 V
    Automatic light control system operates
    Pulse generation
    (See waveform 1)
    I13-23 (RFOG)*3 - Body ground
    L - Body ground
    Rear fog light switch input
    Rear fog light switch on
    Below 1 V
    Rear fog light switch off
    Pulse generation
    I13-27 (FFOG) - Body ground
    V - Body ground
    Front fog light switch input
    Front fog light switch on
    Below 1 V
    Front fog light switch off
    Pulse generation
    I13-28 (A) - Body ground
    G - Body ground
    Light control switch AUTO position signal input
    Light control switch in AUTO position
    Below 1 V
    Light control switch not in AUTO position
    Pulse generation
    I13-29 (HEAD) - Body ground
    P - Body ground
    Light control switch head position input
    Light control switch in head position
    Below 1 V
    Light control switch not in head position, power switch off
    Pulse generation
    Light control switch not in head position, power switch on (IG)
    11 to 14 V
    I13-30 (TAIL) - Body ground
    W - Body ground
    Light control switch tail position signal input
    Light control switch in tail or head position
    Below 1 V
    Light control switch in neither tail nor head position, power switch off
    Pulse generation
    Light control switch in neither tail nor head position, power switch on (IG)
    11 to 14 V

    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/ Rear Fog Light
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



      B113714E01
    1. Waveform 1
      Item
      Content
      Tool setting
      5 V/DIV., 5 ms./DIV.

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.


CHECK POWER MANAGEMENT CONTROL ECU

C146689E44

  1. Disconnect the A38 power management control ECU connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A38-15 (BL) - Body ground
    W - Body ground
    Back-up light signal
    Power switch on (IG), shift lever not in R
    Below 1 V
    Power switch on (IG), shift lever in R
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.