Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Power switch on (ACC) signal/ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    IG SW
    Power switch on (IG) signal/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    RR Door Courtesy SW
    Rear door courtesy light switch RH signal/ON or OFF
    ON: Rear door RH open
    OFF: Rear door RH closed
    -
    RL Door Courtesy SW
    Rear door courtesy light switch LH signal/ON or OFF
    ON: Rear door LH open
    OFF: Rear door LH closed
    -
    FR Door Lock Pos
    Front door RH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FR Door Courtesy
    Front door courtesy light switch RH signal/ON or OFF
    ON: Front door RH closed
    OFF: Front door RH open
    -
    FL Door Lock Pos
    Front door LH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    FL Door Courtesy
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH closed
    OFF: Front door LH open
    -
    RR-Door Lock Pos SW
    Rear door RH unlock detection switch signal/ON or OFF
    ON: Rear door LH locked and rear door RH unlocked
    ON: Rear door LH unlocked and rear door RH locked
    ON: Rear door LH and rear door RH unlocked
    OFF: Rear door LH and rear door RH locked
    -
    RL-Door Lock Pos SW
    Rear door LH unlock detection switch/ON or OFF
    ON: Rear door LH locked and rear door RH unlocked
    ON: Rear door LH unlocked and rear door RH locked
    ON: Rear door LH and rear door RH unlocked
    OFF: Rear door LH and rear door RH locked
    -
    Luggage Courtesy SW
    Luggage compartment door courtesy switch signal/ON or OFF
    ON: Luggage compartment door open
    OFF: Luggage compartment door closed
    -
    Interior Light Control
    Operation of the illuminated entry system/OFF or ON
    OFF: System not operated
    ON: System operated
    Customized value is displayed
    I/L ON W/Door Key Unlock
    Function that lights up the interior lights when the doors are unlocked/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    Lighting Time
    Lighting time of the delay control function (illuminated entry system)/15s, 7.5s or 30s
    15s: 15 seconds
    7.5s: 7.5 seconds
    30s: 30 seconds
    Customized value is displayed
    Room Light when Aprchd
    Function that lights up the interior lights when a key enters any actuation area/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    Inside Foot Light
    Function that lights up the inside handle illumination lights and footwell lights (Always)/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    I/L when ACC OFF
    Function that lights up the interior lights when the power switch is turned from on (IG) or on (ACC) to off/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed
    Light Control
    Function that lights up the inside handle illumination lights and footwell lights (while Driving)/OFF or ON
    OFF: Function disabled
    ON: Function enabled
    Customized value is displayed


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Personal light, rear interior light and power switch illumination
    ON/OFF
    Interior light door switch is on
    Fr Foot Light*1
    Footwell lights
    ON/OFF
    Precondition for using the Active Test to turn lights on and off:
    1. Power switch is turned off just before performing the Active Test.
    Preconditions for using the Active Test to check dimmer controlled illumination:
    1. Power switch is on (IG).
    2. Shift lever is in any position other than P.
    Inside Handle Illumination*1
    Inside handle illumination lights
    ON/OFF
    Precondition for using the Active Test to turn lights on and off:
    1. Power switch is turned off just before performing the Active Test.
    Preconditions for using the Active Test to check dimmer controlled illumination:
    1. Power switch is on (IG).
    2. Shift lever is in any position other than P.
    Relay for Interior Light Auto Cut Function
    Light cut relay
    ON/OFF
    -

    Entry&Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power/Engine SW Light
    Power switch light
    ON/OFF
    When performing this Active Test, make sure the following condition is met:
    The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.

    1. *1: Using this item, the on/off operation and dimmer control of the illumination lights can be checked.