Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE

STEERING KNUCKLE > REMOVAL

for Preparation Click here


NOTICE:
When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE FRONT AXLE ASSEMBLY
(Click here)


2. REMOVE FRONT LOWER BALL JOINT ASSEMBLY
  1. Secure the front axle assembly in a vise using aluminum plates.

    NOTICE:
    When using a vise, do not overtighten it.



    C207073
  1. Remove the cotter pin and nut.



    C165932E02
  1. Install SST to the front lower ball joint assembly as shown in the illustration.

    SST
    09960-20010   (09961-02050, 09961-02050)

    NOTICE:
    Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



    C238957E01
  1. Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

    SST
    09960-20010   (09961-02010, 09961-02050, 09961-02050)
    Text in Illustration 
    *a
    Apply grease
    *b
    Place wrench here

    CAUTION:
    Apply grease to the threads and end of the SST bolt.

    NOTICE:
    1. Install SST so that A and B are parallel.
    2. Be sure to place a wrench on the part indicated in the illustration.
    3. Do not damage the front lower ball joint dust cover.



3. REMOVE FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR


    C238978E01
  1. Using a screwdriver with its tip wrapped with vinyl tape, remove the front No. 1 wheel bearing dust deflector.
    Text in Illustration 
    *1
    Vinyl Tape

    NOTICE:
    Be careful not to damage the steering knuckle.



4. REMOVE FRONT AXLE HUB HOLE SNAP RING


    C238979
  1. Using snap ring pliers, remove the front axle hub hole snap ring.



5. REMOVE FRONT AXLE HUB SUB-ASSEMBLY


    C238975E01
  1. Hold the front axle assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. Using SST, remove the front axle hub sub-assembly.

    SST
    09520-00031  



    C167711E02
  1. Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

    SST
    09555-55010  
    09950-60010   (09951-00440)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to drop the front axle hub sub-assembly.



6. REMOVE FRONT DISC BRAKE DUST COVER


    C238976
  1. Remove the 4 bolts and front disc brake dust cover from the steering knuckle.



7. REMOVE STEERING KNUCKLE


    C202363E01
  1. Place the bearing inner race (outside) on the front axle hub bearing.
    Text in Illustration 
    *1
    Steel Plate
    *2
    V-block

  1. Using SST, a steel plate, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.

    SST
    09950-60010   (09951-00440, 09952-06010)
    09950-60020   (09951-00750)
    09950-70010   (09951-07100)

    NOTICE:
    Keep the steering knuckle level.