Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER SWITCH

B271001E03

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I58-6 (AGND) - Body ground
    -
    G - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    -
    I58-7 (TXCT) - I58-6 (AGND)
    Input
    GR - G
    Immobiliser communication input
    Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -
    I58-8 (CODE) - I58-6 (AGND)
    Output
    SB - G
    Immobiliser communication output
    Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -
    I58-10 (VC5) - I58-6 (AGND)
    Input
    LG - G
    Transponder key amplifier power supply
    Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -

  2. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I58-7 (TXCT) - I58-6 (AGND)
    Input
    GR - G
    Signal input from certification ECU (smart key ECU assembly)
    (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
    Power switch off, key not in cabin, within 30 seconds after power switch pressed
    Pulse generation
    (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response

      HINT:
      If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above

    I58-8 (CODE) - I58-6 (AGND)
    Output
    SB - G
    Signal output to certification ECU (smart key ECU assembly)
    (Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
    Power switch off, power switch pressed with key held near power switch*
    Pulse generation
    (See waveform 2)
    I58-10 (VC5) - I58-6 (AGND)
    Input
    LG - G
    Transponder key amplifier power supply
    (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
    Power switch off, key not in cabin, within 30 seconds after power switch pressed
    Pulse generation
    (See waveform 3)
    If the result is not as specified, the power switch may have a malfunction.

    HINT:
    *: Remove the key battery before performing this inspection.



  3. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B051052E14
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I58-7 (TXCT) - I58-6 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Power switch off, key not in cabin, within 30 seconds after power switch pressed



    2. B368716E01
    3. Waveform 2 (Reference)
      Text in Illustration 
      *a
      Waveform
      *b
      Waveform (detail)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I58-8 (CODE) - I58-6 (AGND)
      Tool Setting
      1. Waveform
        1 V/DIV., 20 ms./DIV.
      2. Waveform (detail)
        2 V/DIV., 100 μs./DIV.
      Condition
      Power switch off, power switch pressed with key held near power switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    4. B216007E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I58-10 (VC5) - I58-6 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Power switch off, key not in cabin, within 30 seconds after power switch pressed


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B278932E05

  1. Disconnect the I86 and I87 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I87-5 (+B) - I86-1 (E)
    Input
    SB - W-B
    +B power supply
    Always
    11 to 14 V
    -
    I87-4 (CUTB) - I86-1 (E)
    Input
    W - W-B
    Dark current cut pin
    Always
    11 to 14 V
    -
    I86-1 (E) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -

  3. Reconnect the I86 and I87 certification ECU (smart key ECU assembly) connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I87-16 (IG) - I86-1 (E)
    Input
    LG - W-B
    Ignition power supply
    Power switch off → on (IG)
    Below 1 V → 11 to 14 V
    Ignition Switch
    I86-8 (IND) - I86-1 (E)
    Output
    L - W-B
    Security indicator output
    Power switch off → on (IG)
    Pulse generation
    → Below 2 V
    -
    I87-3 (TXCT) - I86-6 (AGND)
    Output
    GR - G
    Signal output to transponder key amplifier
    Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response
    I87-13 (CODE) - I86-6 (AGND)
    Input
    SB - G
    Signal input from transponder key amplifier
    Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    I87-9 (VC5) - I86-6 (AGND)
    Output
    LG - G
    Transponder key amplifier power supply
    Power switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    I86-6 (AGND) - Body ground
    -
    G - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    I87-10 (EFII) - I86-1 (E)
    Input
    G - W-B
    EFI communication input
    (Signal input from power management control ECU to certification ECU (smart key ECU assembly))
    Power switch off
    11 to 14 V
    1. B2799
    2. B279A
    3. Engine Start Request
    4. EFI Code Receive
    I87-14 (EFIO) - I86-1 (E)
    Output
    L - W-B
    EFI communication output
    (Signal output from certification ECU (smart key ECU assembly) to power management control ECU)
    Power switch off
    Below 1 V

  5. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I87-3 (TXCT) - I86-6 (AGND)
    Output
    GR - G
    Signal output to transponder key amplifier
    (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into power switch, and then transmitted by transponder key amplifier antenna as radio waves)
    Power switch off, key not in cabin, within 30 seconds after power switch pressed
    Pulse generation
    (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response
    I87-13 (CODE) - I86-6 (AGND)
    Input
    SB - G
    Signal input from transponder key amplifier
    (Radio waves from transponder key amplifier built into power switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
    Power switch off, power switch pressed with key held near power switch*
    Pulse generation
    (See waveform 2)
    I87-9 (VC5) - I86-6 (AGND)
    Output
    LG - G
    Transponder key amplifier power supply
    (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into power switch activated)
    Power switch off, key not in cabin, within 30 seconds after power switch pressed
    Pulse generation
    (See waveform 3)
    I87-10 (EFII) - I86-1 (E)
    Input
    G - W-B
    EFI communication input
    (Signal input from power management control ECU to certification ECU (smart key ECU assembly))
    Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 4)
    1. B2799
    2. B279A
    3. Engine Start Request
    4. EFI Code Receive
    I87-14 (EFIO) - I86-1 (E)
    Output
    L - W-B
    EFI communication output
    (Signal output from certification ECU (smart key ECU assembly) to power management control ECU)
    Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 5)
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

    HINT:
    *: Remove the key battery before performing this inspection.



  6. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B051052E14
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I87-3 (TXCT) - I86-6 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Power switch off, key not in cabin, within 30 seconds after power switch pressed



    2. B368716E01
    3. Waveform 2 (Reference)
      Text in Illustration 
      *a
      Waveform
      *b
      Waveform (detail)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I87-13 (CODE) - I86-6 (AGND)
      Tool Setting
      1. Waveform
        1 V/DIV., 20 ms./DIV.
      2. Waveform (detail)
        2 V/DIV., 100 μs./DIV.
      Condition
      Power switch off, power switch pressed with key held near power switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    4. B216007E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I87-9 (VC5) - I86-6 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Power switch off, key not in cabin, within 30 seconds after power switch pressed



    6. Waveform 4 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      I87-10 (EFII) - I86-1 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected



    7. Waveform 5 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      I87-14 (EFIO) - I86-1 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

B118684E73

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I24-1 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    I24-3 (IGE) - I24-1 (GND)
    Input
    SB - W-B
    Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly))
    Steering lock motor operates when all conditions met, and then door opened:
    1. Shift lever in P
    2. Steering unlocked
    3. Power switch turned off
    Pulse generation
    (See waveform 1)
    1. Power Supply Short
    2. Unlock Request Receive
    3. Lock Request Receive
    I24-4 (SLP1) - I24-1 (GND)
    Output
    P - W-B
    Steering lock bar position signal (signal output from steering unlock sensor)
    Steering locked → unlocked*1
    11 to 14 V → Below 1.5 V
    1. Push Start Error
    2. Sensor Value
    I24-6 (IG2) - I24-1 (GND)
    Input
    LG - W-B
    IG signal (IG2 power supply input for steering lock motor)
    Power switch off → on (IG)
    Below 1 V → 11 to 14 V
    1. B2788
    2. Ignition Switch
    I24-7 (B) - Body ground
    Output
    B - Body ground
    Constant power supply
    Always
    11 to 14 V
    B2788
    If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may have a malfunction.

    HINT:
    *1: The steering locks when any door is opened with the shift lever in P and the power switch off. The steering unlocks when the power switch is turned on (ACC).



  2. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      C221561E01
    1. Waveform 1 (Reference)
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating
      Measurement Condition 
      Item
      Content
      Tester Connection
      I24-3 (IGE) - I24-1 (GND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Steering lock motor operates when all conditions met, and then door opened:
      1. Shift lever in P
      2. Steering unlocked
      3. Power switch turned off


CHECK POWER MANAGEMENT CONTROL ECU

B220221E03


Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
A38-1 (+B2) - I3-5 (E01)
Input
B - W-B
IG power supply
Power switch on (IG)
11 to 14 V
-
A39-3 (+B1) - I3-5 (E01)
Input
B - W-B
IG power supply
Power switch on (IG)
11 to 14 V
-
A38-4 (MREL) - I3-5 (E01)
Input
V - W-B
IG power supply
Power switch on (IG)
11 to 14 V
-
I3-1 (AM22) - I3-6 (E1)
Input
SB - BR
+B power supply
Always
11 to 14 V
-
I3-5 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
I3-6 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
I4-4 (E12) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
I4-5 (E02) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
I4-7 (AM21) - I3-6 (E1)
Input
L - BR
+B power supply
Always
11 to 14 V
-
I4-28 (IMO) - I3-6 (E1)
Input
G - BR
Certification ECU (smart key ECU assembly) communication input
Power switch off
11 to 14 V
-
I4-28 (IMO) - I3-6 (E1)
Input
G - BR
Certification ECU (smart key ECU assembly) communication input
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
Pulse generation
(See waveform 1)
-
I4-29 (IMI) - I3-6 (E1)
Output
L - BR
Certification ECU (smart key ECU assembly) communication output
Power switch off
Below 1 V
-
I4-29 (IMI) - I3-6 (E1)
Output
L - BR
Certification ECU (smart key ECU assembly) communication output
Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
Pulse generation
(See waveform 2)
-


  1. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      I4-28 (IMO) - I3-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      I4-29 (IMI) - I3-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected