STEERING PAD > DISPOSAL |
| 1. PRECAUTION |
| 2. DISPOSE OF HORN BUTTON ASSEMBLY (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect SST to the 12 V battery.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *a | 12 V Battery |
![]() |
Check the function of SST.
Press the SST activation switch and check that the LED of the SST activation switch comes on.
Disconnect SST from the 12 V battery.
Refer to Precaution (Click here).
Disconnect the cable from the negative (-) auxiliary battery terminal.
Remove the lower steering column cover .
Disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.
![]() |
Slide the slider to release the lock, and then disconnect the yellow airbag connector from the spiral cable with sensor sub-assembly.
| *a | Slider |
Install SST.
![]() |
After connecting the following SST to each other, connect them to the spiral cable with sensor sub-assembly.
![]() |
Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.
| *a | 12 V Battery |
| *b | 10 m (32.8 ft.) or more |
Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press the SST activation switch to deploy the airbag.
| 3. DISPOSE OF HORN BUTTON ASSEMBLY (When Not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect SST to the 12 V battery.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *a | 12 V Battery |
![]() |
Check the function of SST.
Press the SST activation switch and check that the LED of the SST activation switch comes on.
Disconnect SST from the 12 V battery.
Remove the horn button assembly (Click here).
![]() |
Using braided wire, tie down the horn button assembly to an unneeded tire and wheel set.
| *a | Wire Diameter |
| *b | Stripped Wire Cross Sectional Area |
![]() |
After connecting the following SST to each other, connect them to the horn button assembly.
![]() |
Wind 3 wires at least 2 times each around each of the pins.
| *a | 2 times or more |
![]() |
Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie each side of the horn button assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.
| *a | Width |
| *b | Inner Diameter |
![]() |
Install SST.
Connect the SST connector.
![]() |
Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the wheel.
| *a | 10 m (32.8 ft.) or more |
Cover the horn button assembly (using a cardboard box).
![]() |
Cover the horn button assembly with a cardboard box.
| *a | Weight |
Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).
Cover the horn button assembly (using tires).
![]() |
Place at least 3 tires without wheels onto the tire and wheel set to which the horn button assembly is tied.
| *a | Tires (3 or more) |
| *b | Inner Diameter |
| *c | Width |
Place a tire and wheel set on top.
![]() |
Tie the tires together with the 2 wires.
Deploy the airbag.
![]() |
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
| *1 | Horn Button Assembly |
| *a | Using a Cardboard Box |
| *b | Using Tires |
| *c | 12 V Battery |
| *d | 10 m (32.8 ft.) or more |
Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.
Press the SST activation switch to deploy the airbag.
Dispose of the horn button assembly.
Remove the horn button assembly from the tire and wheel set.
Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.