Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR

SIDE AIRBAG SENSOR > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

CAUTION:
Be sure to read Precaution thoroughly before servicing.
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    A259067
  1. Disengage the claw to remove the luggage trim service hole cover.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



4. REMOVE FRONT DOOR SCUFF PLATE


    B395175E01
  1. Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

  1. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

  1. Disengage the 6 claws (C) to remove the front door scuff plate LH.



5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:
Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.



6. REMOVE REAR DOOR SCUFF PLATE


    B395176E01
  1. Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.

  1. Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.

  1. Disengage the 4 claws (C) to remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the front side of the rear door scuff plate LH.



7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the center pillar lower garnish.



8. REMOVE CENTER PILLAR LOWER GARNISH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



9. REMOVE SIDE AIRBAG SENSOR ASSEMBLY
  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



  1. Disconnect the connector from the side airbag sensor assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


      B279712E01


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Slide
      *b
      Push

    2. Push down the white housing lock again and disconnect the connector.

      NOTICE:
      Do not push down the part (A) shown in the illustration when disconnecting the connector.

  1. Remove the bolt and side airbag sensor assembly from the vehicle body.

    NOTICE:
    Loosen the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.



  1. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296256E01


    Text in Illustration 
    *a
    Correct
    *b
    Incorrect