Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY

HV RELAY ASSEMBLY > INSPECTION

for Preparation Click here



1. INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY


  1. Inspect SMRB.



      A259731E05
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A-1 (+) - Q2-1 (CBI)
      Auxiliary battery voltage is not applied between terminals O9-1 (SMRB) and O9-2 (GND)
      10 kΩ or higher
      A-1 (+) - Q2-1 (CBI)
      Auxiliary battery voltage is applied between terminals O9-1 (SMRB) and O9-2(GND)
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Hybrid Battery Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O9-1 (SMRB) - O9-2 (GND)
      -40 to 80°C (-40 to 176°F)
      25.0 to 59.0 Ω

      If the result is not as specified, replace the hybrid battery junction block assembly or electric vehicle fuse.



  1. Inspect SMRG.



      A259731E06
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      q1-1(-) - Q3- 1(CEI)
      Auxiliary battery voltage is not applied between terminals O9-3(SMRG) and O9-2(GND)
      10 kΩ or higher
      q1-1(-) - Q3- 1(CEI)
      Auxiliary battery voltage is applied between terminals O9-3(SMRG) and O9-2(GND)
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Hybrid Battery Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O9-3(SMRG) - O9-2(GND)
      -40 to 80°C (-40 to 176°F)
      25.0 to 59.0 Ω

      If the result is not as specified, replace the hybrid battery junction block assembly.



  1. Inspect SMRP.



      A259731E13
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Q3-1 (CEI) - q1-1 (-))
      Auxiliary battery voltage is not applied between terminals O9-4(SMRP) and O9-2(GND)
      10 kΩ or higher
      Q3-1 (CEI) - q1-1 (-))
      Auxiliary battery voltage is applied between terminals O9-4(SMRP) and O9-2(GND)
      28.5 to 31.5 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Hybrid Battery Junction Block Assembly)

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O9-4(SMRP) and O9-2(GND)
      -40 to 80°C (-40 to 176°F)
      112 to 274 Ω

      If the result is not as specified, replace the hybrid battery junction block assembly.