Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD


3. REMOVE FRONT WHEEL


4. REMOVE HORN BUTTON ASSEMBLY
(Click here)


5. REMOVE STEERING WHEEL ASSEMBLY


    C310282E01
  1. Remove the steering wheel assembly set nut.
    Text in Illustration 
    *a
    Matchmark

  1. Put matchmarks on the steering wheel assembly and steering main shaft.

  1. Disconnect the connectors from the spiral cable sub-assembly.



    C310283E01
  1. Using SST, remove the steering wheel assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05070)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



6. REMOVE FRONT DOOR SCUFF PLATE RH (w/o Driver Side Knee Airbag)

HINT:
Use the same procedure for RHD and LHD .



7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (w/o Driver Side Knee Airbag)

HINT:
Use the same procedure for RHD and LHD .



8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (w/o Driver Side Knee Airbag)

HINT:
Use the same procedure for RHD and LHD .



9. REMOVE INSTRUMENT SIDE PANEL RH (w/o Driver Side Knee Airbag)

HINT:
Use the same procedure for RHD and LHD .



10. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

HINT:
Use the same procedure for RHD and LHD .



11. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

HINT:
Use the same procedure for RHD and LHD .



12. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
(Click here)


13. REMOVE LOWER STEERING COLUMN COVER


    C241154
  1. Remove the 2 screws.



    C241155
  1. Push the right and left sides of the lower steering column cover, and disengage the 2 claws.



    C241156
  1. Insert a finger into the opening of the tilt lever of the lower steering column cover to disengage the claw and remove the lower steering column cover.



14. REMOVE UPPER STEERING COLUMN COVER


    C241158
  1. Disengage the 4 clips and 2 guides from the upper steering column cover.



    C241157
  1. Disengage the 2 claws to remove the upper steering column cover.



15. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C241159
  1. Disengage the 3 claws to remove the turn signal switch assembly with spiral cable sub-assembly from the steering post assembly.

    NOTICE:
    1. Do not replace the spiral cable with the auxiliary battery connected and the power switch on (IG).
    2. Do not rotate the spiral cable with the auxiliary battery connected and the power switch on (IG).
    3. Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



16. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY


    C236186
  1. Using a screwdriver, loosen the clamp as shown in the illustration.



    C239330E01
  1. Put matchmarks on the steering intermediate shaft assembly and the steering link assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt and separate the steering intermediate shaft assembly from the steering link assembly.



17. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for LHD)


    C283848E01
  1. Disengage the wire harness clamp from the No. 2 air duct sub-assembly.
    Text in Illustration 
    *1
    Guide
    *2
    Clamp
    *3
    Claw

  1. Disconnect the connector from the footwell light.

  1. Using a screwdriver, Disengage the 2 claws and guide.

    NOTICE:
    Do not lift the claw excessively.

    HINT:
    When disengaging the claw, insert a screwdriver under the end of the claw and lift it gently.

  1. Disengage the clamp to remove the No. 2 air duct sub-assembly.



18. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD)


    C283787
  1. Disconnect the connector from the footwell light.

  1. Remove the bolt.

  1. Disengage the 2 claws to remove the No. 2 air duct sub-assembly.



19. REMOVE STEERING POST ASSEMBLY
  1. Disconnect the connectors and disengage the wire harness clamps from the steering post assembly.



    C236189
  1. Disconnect the 2 connectors.



    C236190
  1. Disengage the clamp.



    C236191
  1. Remove the bolt to separate the ground wire.

  1. Remove the 4 nuts and the steering post assembly.



20. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY


    C236192E01
  1. Remove the bolt and slide the steering intermediate shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not remove the steering intermediate shaft assembly from the steering column assembly.

  1. Put matchmarks on the steering intermediate shaft assembly and the steering column assembly.

  1. Remove the steering intermediate shaft assembly from the steering column assembly.