Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/o EGR System)

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stored the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No.
DTC Detection Condition
Trouble Area
P0420
The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic).
  1. Gas leak from exhaust system
  2. Air fuel ratio sensor (sensor 1)
  3. Heated oxygen sensor (sensor 2)
  4. Exhaust manifold converter sub-assembly (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)

CATALYST LOCATION


A263305E01


Text in Illustration 
*1
Air Fuel Ratio Sensor (Sensor 1)
*2
Heated Oxygen Sensor (Sensor 2)
*3
TWC: Front Catalyst
*4
TWC: Rear Catalyst
*5
Center Exhaust Pipe Assembly
*6
Tail Exhaust Pipe Assembly
*7
Exhaust Manifold Converter Sub-assembly
*8
Front Exhaust Pipe Assembly

NOTICE:
Replace the exhaust manifold converter sub-assembly (*7) and the front exhaust pipe assembly (*8) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *1 and heated oxygen sensor *2)


MONITOR STRATEGY


Required Sensors/Components (Main)
Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor
Mass air flow meter sub-assembly
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Auxiliary battery voltage
11 V or higher
Intake air temperature
-10°C (14°F) or higher
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or higher
Idling
Off
Engine speed
Less than 4000 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Engine load
10% or higher, and less than 70%
All of the following conditions are met
-
Mass air flow rate
2.5 gm/sec or more, and less than 50 gm/sec
Front catalyst temperature (estimated)
530°C (986°F) or higher, and less than 770°C (1418°F)
Rear catalyst temperature (estimated)
400°C (752°F) or higher, and less than 700°C (1292°F)

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283969E53

  1. Connect the GTS to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off and wait for at least 30 seconds.
  6. Turn the power switch on (IG) and turn the GTS on.
  7. Put the engine in inspection mode (maintenance mode) (Click here).
  8. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  9. Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  10. Turn the power switch off and wait for at least 30 seconds [C].
  11. Turn the power switch on (IG) and turn the GTS on.
  12. Put the engine in inspection mode (maintenance mode) (Click here ).
  13. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].
  14. Drive the vehicle at approximately 75 km/h (47 mph) for 10 minutes or more [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  18. Input the DTC: P0420.
  19. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform the following procedure.

  20. Drive the vehicle at a speed 100 km/h (62 mph) for 10 minutes or more [G].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  21. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
  22. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  23. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  24. Input the DTC: P0420.
  25. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A118003E56

  1. (a) Connect the GTS to the DLC3 [A].
  2. (b) Turn the power switch on (IG) and turn the GTS on [B].
  3. (c) Put the engine in inspection mode (maintenance mode) (Click here) [C].
  4. (d) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature stabilizes [D].
  5. (e) Run the engine at an engine speed of 2500 rpm for at least 3 minutes [E].

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [E] after charging control has completed.

  6. (f) While running the engine at 2500 rpm for 2 seconds and 1500 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS [F].

HINT:
  1. If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or there is noise in the waveform of either sensor, the sensor may be malfunctioning.
  2. If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume Active Test using the GTS.
  3. If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E09


INSPECTION PROCEDURE

HINT:
  1. If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).
  2. Sensor 1 refers to the sensor closest to the engine assembly.
  3. Sensor 2 refers to the sensor farthest away from the engine assembly.
  4. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    DTC P0420 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, warm up the engine after charging control has completed.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2.

  1. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

    HINT:
    1. Change the fuel injection volume within the range of - 12% to 12%. The injection volume can be changed in fine gradations.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (Air fuel ratio)
    12%
    Rich
    Below 3.1 V
    -12%
    Lean
    Higher than 3.4 V
    O2S B1S2
    (Heated oxygen)
    12%
    Rich
    Higher than 0.55 V
    -12%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS Voltage B1S1
    Status
    O2S B1S2
    Actual air fuel ratio, air fuel ratio sensor and
    heated oxygen sensor condition
    Misfire
    Main Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leak from exhaust system
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air fuel ratio lean
    May occur
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leak from exhaust system
    D
    Rich
    Rich
    Actual air fuel ratio rich
    -
    1. Extremely rich or lean actual air fuel ratio
    2. Gas leak from exhaust system
    1. Lean: During Control the Injection Volume, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



B
Go to step 5

C
Go to step 6

D
Go to step 8
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NOTICE:
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (Click here).

  1. Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).


NEXT

END 

5.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NEXT
Go to step 11

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


7.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).



NEXT
Go to step 11

8.CHECK FOR EXHAUST GAS LEAK
  1. Check the exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .



NEXT
Go to step 11

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace exhaust gas leak point.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    DTC is not output
    (No pending DTCs output)
    B



B
END
A


12.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NOTICE:
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) and the front exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (Click here).

  1. Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).


NEXT

END