CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (RHD Models) |
| Symptom | Trouble Area |
| No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3. |
|


| 1.CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE) |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Disconnect the DLC3 branch line connector (I96) from the CAN junction RH connector.
| *a | Rear view of wire harness connector (to CAN Junction RH Connector) |
| *b | to DLC3 |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR SHORT TO +B IN CAN BUS LINE |
Reconnect the DLC3 branch line connector (I96) to the CAN junction RH connector.
![]() |
Disconnect the connectors from the CAN junction LH connector and CAN junction RH connector one at a time.
| *1 | DLC3 |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

| *1 | Power Management Control ECU | *2 | Main Body ECU (Multiplex Network Body ECU) |
| *3 | Air Conditioning Amplifier Assembly | *4 | Airbag Sensor Assembly |
| *5 | Power Steering ECU Assembly | *6 | ECM |
| *7 | Radio and Display Receiver Assembly | *8 | Combination Meter Assembly |
| *9 | DLC3 | *10 | Smart Key ECU Assembly (Certification ECU) |
| *11 | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | *12 | Steering Sensor |
| *13 | Clearance Warning Assembly ECU | *14 | CAN Junction RH Connector |
| *15 | CAN Junction LH Connector | - | - |

| *a | Component without harness connected (CAN Junction LH Connector) | - | - |
| CAN Junction LH Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector) | I93 | B | W |
| Radio and display receiver assembly | I107 | R | W |
| ECM | I104 | G | W |
| Power steering ECU assembly | I100 | L | W |
| Airbag sensor assembly | I103 | Y | W |
| Air conditioning amplifier assembly | I102 | V | W |
| Main body ECU (Multiplex network body ECU) | I95 | P | W |
| Power management control ECU | I109 | BE | W |

| *a | Component without harness connected (CAN Junction RH Connector) | - | - |
| CAN Junction RH Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| Clearance warning ECU assembly | I111 | P | W |
| Steering sensor | I97 | V | W |
| Brake booster with master cylinder assembly (Skid control ECU) | I110 | Y | W |
| Smart key ECU assembly (Certification ECU) | I106 | L | W |
| DLC3 | I96 | G | W |
| Combination meter assembly | I94 | R | W |
| CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector) | I101 | B | W |
| Symptom | Proceed to |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector. (There is a short to +B in the CAN main bus lines between the CAN junction LH connector and CAN junction RH connector.) | A |
| The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or more) when a connector is disconnected from the CAN junction connector. (There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) | B |
When there is a short to +B in one or more of the bus lines that connect to an ECU (or sensor):
Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to +B). Check that the resistance shown on the tester is normal (6 kΩ or more) to confirm that there is a short to +B in the one bus line only.
When there is no short to +B in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN junction LH connector and CAN junction RH connector.
|
| ||||
| A | |
| 3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C RH) |
![]() |
Disconnect the CAN main bus line connector (I101) from the CAN junction RH connector.
| *a | Rear view of wire harness connector (to CAN Junction RH Connector) |
| *b | to CAN Junction LH Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH - CAN J/C RH) |
Reconnect the CAN main bus line connector (I101) to the CAN junction RH connector.
![]() |
Disconnect the CAN main bus line connector (I93) from the CAN junction LH connector.
| *a | Rear view of wire harness connector (to CAN Junction LH Connector) |
| *b | to CAN Junction RH Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 5.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR) |
Reconnect the connector of the bus line that is shorted to +B to the CAN junction connector (the connector that caused the bus line resistance to change to 6 kΩ or more when it was disconnected).
![]() |
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to +B is connected (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||