Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (LHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3.
  1. Short to ground in CAN main bus line
  2. Short to ground in CAN branch line
  3. Power management control ECU
  4. ECM
  5. Main body ECU (multiplex network body ECU)
  6. Combination meter assembly
  7. Brake booster with master cylinder assembly (skid control ECU)
  8. Steering sensor
  9. Power steering ECU assembly
  10. Airbag sensor assembly
  11. Air conditioning amplifier assembly
  12. Smart key ECU assembly (certification ECU)
  13. Radio and display receiver assembly
  14. Clearance warning ECU assembly
  15. CAN junction LH connector
  16. CAN junction RH connector

WIRING DIAGRAM


C178194E01


C293488E01


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 11 seconds.
  6. After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
  3. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (DLC3 BRANCH LINE)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C248236E01
  1. Disconnect the DLC3 branch line connector (I96) from the CAN junction LH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction LH Connector)
    *b
    to DLC3

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E49
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
OK


2.CHECK FOR SHORT TO GND IN CAN BUS LINE
  1. Reconnect the DLC3 branch line connector (I96) to the CAN junction LH connector.



    C210421E49
  1. Disconnect the connectors from the CAN junction LH connector and CAN junction RH connector one at a time.

    HINT:
    Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN junction LH connector and CAN junction RH connector.

    Text in Illustration 
    *1
    DLC3



  1. Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.


    C293489E01


    Text in Illustration 
    *1
    ECM
    *2
    Air Conditioning Amplifier Assembly
    *3
    Airbag Sensor Assembly
    *4
    Smart Key ECU Assembly (Certification ECU)
    *5
    Power Steering ECU Assembly
    *6
    Radio and Display Receiver Assembly
    *7
    Clearance Warning ECU Assembly
    *8
    Combination Meter Assembly
    *9
    Power Management Control ECU
    *10
    DLC3
    *11
    Brake Booster with Master Cylinder Assembly (Skid Control ECU)
    *12
    Steering Sensor
    *13
    Main Body ECU (Multiplex Network Body ECU)
    *14
    CAN Junction RH Connector
    *15
    CAN Junction LH Connector
    -
    -

    C248228E01


    Text in Illustration 
    *a
    Component without harness connected
    (CAN Junction LH Connector)
    -
    -

    Wiring Color 
    CAN Junction LH Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector)
    I93
    B
    W
    Combination meter assembly
    I94
    R
    W
    Power management control ECU
    I109
    G
    W
    DLC3
    I96
    L
    W
    Brake booster with master cylinder assembly (skid control ECU)
    I110
    Y
    W
    Steering sensor
    I97
    V
    W
    Main body ECU (multiplex network body ECU)
    I95
    P
    W

    C293490E01


    Text in Illustration 
    *a
    Component without harness connected
    (CAN Junction RH Connector)
    -
    -

    Wiring Color 
    CAN Junction RH Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    Clearance warning ECU assembly
    I111
    BE
    W
    ECM
    I104
    P
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    Airbag sensor assembly
    I99
    Y
    W
    Smart key ECU assembly (certification ECU)
    I106
    L
    W
    Power steering ECU assembly
    I98
    G
    W
    Radio and display receiver assembly
    I107
    R
    W
    CAN main bus line (bus line connecting CAN junction LH connector and CAN junction RH connector)
    I101
    B
    W

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to GND in 2 or more CAN bus lines.


    Result:

    Symptom
    Proceed to
    The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the CAN junction connector. (There is a short to GND in the CAN main bus lines between the CAN junction LH connector and CAN junction RH connector.)
    A
    The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or more) when a connector is disconnected from the CAN junction connector. (There is a short to GND in one of the areas that relate to the disconnected bus lines.)
    B

  1. When there is a short to GND in one or more of the bus lines that connect to an ECU (or sensor):

    1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or more) to confirm that there is a short to GND in the one branch line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

  1. When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:

    1. With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN junction LH connector and CAN junction RH connector.



B
Go to step 5
A


3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH)


    C248239E01
  1. Disconnect the CAN main bus line connector (I93) from the CAN junction LH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction LH Connector)
    *b
    to CAN Junction RH Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E49
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher

    Text in Illustration 
    *1
    DLC3



NG
REPLACE CAN JUNCTION LH CONNECTOR
OK


4.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH - CAN J/C RH)
  1. Reconnect the CAN main bus line connector (I93) to the CAN junction LH connector.



    C248240E01
  1. Disconnect the CAN main bus line connector (I101) from the CAN junction RH connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN Junction RH Connector)
    *b
    to CAN Junction LH Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C210421E49
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH - CAN J/C RH)
OK

REPLACE CAN JUNCTION RH CONNECTOR 

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
  1. Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or more when it was disconnected).



    C210421E49
  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to GND is connected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR