Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > TERMINALS OF ECU

for Preparation Click here



TERMINALS OF ECU

C156569E02


Text in Illustration 
*a
Component without harness connected
(Skid Control ECU (Brake Booster with Master Cylinder Assembly))
-
-

Terminal No. (Symbol)
Terminal Description
1 (MRI1)
Motor power supply input 1
2 (MRI2)
Motor power supply input 2
3 (STP0)
Stop light control relay (STOP relay) output
4
- (Not used)
5 (FR-)
Front speed sensor RH (-) signal input
6 (STP2)
Stop light control relay (STOP relay) input
7 (RL-)
Rear speed sensor LH (-) signal input
8 (CSW)
VSC OFF switch (vehicle stability control switch) input
9 (RR-)
Rear speed sensor RH (-) signal input
10
- (Not used)
11 (SP1)
Speed sensor signal output
12 (IG2)
IG2 power source input
13
- (Not used)
14 (BI)
+B power source input
15 (BS)
Solenoid power supply input
16 (IG1)
IG1 power source input
17
- (Not used)
18 (FR+)
Front speed sensor RH (+) power supply output
19 (CTY)
Front door courtesy light switch assembly input
20 (RL+)
Rear speed sensor LH (+) power supply output
21
- (Not used)
22 (RR+)
Rear speed sensor RH (+) power supply output
23 (GND6)
Skid control ECU (Brake booster with master cylinder assembly) ground 6
24 (GND5)
Skid control ECU (Brake booster with master cylinder assembly) ground 5
25 (GND4)
Skid control ECU (Brake booster with master cylinder assembly) ground 4
26 (GND3)
Skid control ECU (Brake booster with master cylinder assembly) ground 3
27 (GND2)
Skid control ECU (Brake booster with master cylinder assembly) ground 2
28 (GND)
Skid control ECU (Brake booster with master cylinder assembly) ground
29 (MRO1)
Motor power supply output 1
30 (MRO2)
Motor power supply output 2
31 (FL+)
Front speed sensor LH (+) power supply output
32 (FL-)
Front speed sensor LH (-) signal input
33 (STP)
Stop light switch assembly input
34 (CA2L)
CAN communication line 2 (L)
35 (CA2H)
CAN communication line 2 (H)
36 (LBL)
Brake fluid level warning switch input
37 (CA1H)
CAN communication line 1 (H)
38 (CA1L)
CAN communication line 1 (L)
39 (VCSK)
Brake pedal stroke sensor assembly power supply output
40 (SKS2)
Brake pedal stroke sensor assembly signal input 2
41 (SKG)
Brake pedal stroke sensor assembly ground
42 (SKS)
Brake pedal stroke sensor assembly signal input

TERMINAL INSPECTION


  1. Disconnect the connector and measure the voltage or resistance on the wire harness side.


    C156570E07


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))
    -
    -

    HINT:
    The voltage cannot be measured with the connector connected to the skid control ECU (brake booster with master cylinder assembly) as the connector is watertight.


    Standard 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A28-1 (MRI1) - Body ground
    R - Body ground
    Motor power supply input 1
    Always
    11 to 14 V
    A28-2 (MRI2) - Body ground
    R - Body ground
    Motor power supply input 2
    Always
    11 to 14 V
    A28-3 (STP0) - Body ground
    G - Body ground
    Stop light control relay (STOP relay) output
    Power switch on (IG)
    11 to 14 V
    A28-6 (STP2) - Body ground
    GR - Body ground
    Stop light control relay (STOP relay) input
    Stop light switch assembly ON → OFF
    (Brake pedal depressed → released)
    11 to 14 V → Below 1.5 V
    A28-8 (CSW) - Body ground
    V - Body ground
    VSC OFF switch (vehicle stability control switch) input
    VSC OFF switch (vehicle stability control switch) held ON → OFF (Released)
    Below 1 Ω → 10 kΩ or higher
    A28-12 (IG2) - Body ground
    SB - Body ground
    IG2 power source input
    Power switch on (IG)
    11 to 14 V
    A28-14 (BI) - Body ground
    P - Body ground
    +B power source input
    Always
    11 to 14 V
    A28-15 (BS) - Body ground
    Y - Body ground
    Solenoid power supply input
    Always
    11 to 14 V
    A28-16 (IG1) - Body ground
    SB - Body ground
    IG1 power source input
    Power switch on (IG)
    11 to 14 V
    A28-19 (CTY) - Body ground
    L - Body ground
    Front door courtesy light switch assembly input
    Driver door closed → open
    11 to 14 V → Below 1.5 V
    A28-23 (GND6) - Body ground
    W-B - Body ground
    Skid control ECU (Brake booster with master cylinder assembly) ground 6
    Always
    Below 1 Ω
    A28-24 (GND5) - Body ground
    W-B - Body ground
    Skid control ECU (Brake booster with master cylinder assembly) ground 5
    Always
    Below 1 Ω
    A28-25 (GND4) - Body ground
    W-B - Body ground
    Skid control ECU (Brake booster with master cylinder assembly) ground 4
    Always
    Below 1 Ω
    A28-26 (GND3) - Body ground
    W-B - Body ground
    Skid control ECU (Brake booster with master cylinder assembly) ground 3
    Always
    Below 1 Ω
    A28-27 (GND2) - Body ground
    W-B - Body ground
    Skid control ECU (Brake booster with master cylinder assembly) ground 2
    Always
    Below 1 Ω
    A28-28 (GND) - Body ground
    W-B - Body ground
    Skid control ECU (Brake booster with master cylinder assembly) ground
    Always
    Below 1 Ω
    A28-33 (STP) - Body ground
    SB - Body ground
    Stop light switch assembly input
    Stop light switch assembly ON → OFF
    (Brake pedal depressed → released)
    11 to 14 V → Below 1.5 V
    A28-36 (LBL) - Body ground
    LG - Body ground
    Brake fluid level warning switch input
    Brake fluid level warning switch OFF → ON
    1.84 to 2.16 kΩ → Below 1 Ω