DTC P3107-215 Lost Communication with Airbag System Control Module |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P3107 | 215 | Abnormal communication signal |
|
| 1.CHECK DTC OUTPUT (SRS AIRBAG) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Body / SRS Airbag / DTC.
Check if DTCs are output.
| Result | Proceed to |
| Airbag system DTCs are not output. | A |
| Airbag system DTCs are output. (for Built-in type yaw rate sensor) | B |
| Airbag system DTCs are output. (for Separate type yaw rate sensor) | C |
Turn the power switch off.
|
| ||||
|
| ||||
| A | |
| 2.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Clear DTCs and freeze frame data.
Turn the power switch off.
| NEXT | |
| 3.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
| P3107-215 is not output. | A |
| P3107-215 is output again. | B |
Turn the power switch off.
|
| ||||
| A | |
| 4.CHECK FOR INTERMITTENT PROBLEMS |
|
| ||||
| OK | ||
| ||
| 5.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM) |
Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.
Turn the power switch on (READY).
Measure the waveform.

| Item | Contents |
| Terminal | I47-14 (GSW2) - I47-25 (E1) |
| Equipment Setting | 5V/DIV., 500ms/DIV. |
| Condition | Power switch on (READY) |
| Result | Proceed to |
| The waveform appears as shown in the illustration. | A |
| The waveform differs from the one shown in the illustration. | B |
| *a | Component with harness connected (Airbag Sensor Assembly (for Built-in Type Yaw Rate Sensor)) |
| *b | Component with harness connected (Airbag Sensor Assembly (for Separate Type Yaw Rate Sensor)) |
Turn the power switch off.
|
| ||||
| A | ||
| ||
| 6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).
|
| ||||
| OK | |
| 7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR) |
![]() |
Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.
| *a | Component with harness connected (Airbag Sensor Assembly (for Built-in Type Yaw Rate Sensor)) |
| *b | Component with harness connected (Airbag Sensor Assembly (for Separate Type Yaw Rate Sensor)) |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (+B SHORT) |
![]() |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT Fuse |
![]() |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 Fuse |
![]() |
Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 Fuse |
![]() |
Disconnect connector I47 from the airbag sensor assembly.
| *a | Component without harness connected (Airbag Sensor Assembly (for Built-in Type Yaw Rate Sensor)) |
| *b | Component without harness connected (Airbag Sensor Assembly (for Separate Type Yaw Rate Sensor)) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I3-29 (ABFS) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
| *a | Component with harness connected (Power Management Control ECU) |
Connect the airbag sensor assembly connector.
Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY) |
Disconnect connector I3 from the power management control ECU.
Disconnect connector I47 from the airbag sensor assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Rear view of wire harness connector (to Power Management Control ECU) | *b | Rear view of wire harness connector (to Airbag Sensor Assembly (for Built-in Type Yaw Rate Sensor)) |
| *c | Rear view of wire harness connector (to Airbag Sensor Assembly (for Separate Type Yaw Rate Sensor)) | - | - |
| Tester Connection | Switch Condition | Specified Condition |
| I3-29 (ABFS) - I47-14 (GSW2) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| I3-29 (ABFS) or I47-14 (GSW2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Connect the airbag sensor assembly connector.
Connect the power management control ECU connector.
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES) |
![]() |
Remove the PM IGCT fuse from the No. 2 engine room relay block.
| *1 | No. 2 Engine Room Relay Block |
| *2 | PM IGCT Fuse |
![]() |
Remove the AM2 fuse from the engine room relay block and junction block assembly.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | AM2 Fuse |
![]() |
Remove the ECU-IG2 NO. 1 fuse from the instrument panel junction block assembly.
| *1 | Instrument Panel Junction Block Assembly |
| *2 | ECU-IG2 NO. 1 Fuse |
![]() |
Disconnect connector I47 from the airbag sensor assembly.
| *a | Component without harness connected (Airbag Sensor Assembly (for Built-in Type Yaw Rate Sensor)) |
| *b | Component without harness connected (Airbag Sensor Assembly (for Separate Type Yaw Rate Sensor)) |
Disconnect all the connectors from the power management control ECU.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I3-29 (ABFS) - A38-2 (+B2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-5 (+B1) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-1 (AM22) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-7 (AM21) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-6 (MREL) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-1 (IG2) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-1 (ACCD) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I4-2 (IG1D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A39-2 (IG2D) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - I3-14 (SPDI) | Power switch off | 10 kΩ or higher |
| I3-29 (ABFS) - A38-16 (GI) | Power switch off | 10 kΩ or higher |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
Connect the power management control ECU connectors.
Connect the airbag sensor assembly connector.
Install the PM IGCT fuse, AM2 fuse and ECU-IG2 NO. 1 fuse.
|
| ||||
| OK | ||
| ||