Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

SMART ENTRY AND START SYSTEM (for Start Function) > TERMINALS OF ECU

for Preparation Click here



CHECK POWER MANAGEMENT CONTROL ECU

C146689E45

  1. Disconnect the A39, I3 and I4 connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    A39-2 (IG2D) - Body ground
    Output
    R - Body ground
    IG2 signal
    20°C (68°F)
    Approximately 302.97 Ω
    IG2 Relay Monitor(Outside)
    A39-23 (STP) - Body ground
    Input
    W - Body ground
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    9 V or higher → 1 V or less
    Stop Light Switch1
    I3-1 (AM22) - Body ground
    Input
    SB - Body ground
    Power source
    Power switch off
    11 to 14 V
    -
    I4-7 (AM21) - Body ground
    Input
    L - Body ground
    Power source
    Power switch off
    11 to 14 V
    -
    I4-16 (SLP) - Body ground
    Input
    P - Body ground
    Steering lock position signal
    Always
    10 kΩ or higher
    Steering Unlock Switch
    I3-5 (E01) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    I4-5 (E02) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    I3-6 (E1) - Body ground
    -
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    -
    I4-4 (E12) - Body ground
    -
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    -
    I4-17 (SSW2) - Body ground
    Input
    V - Body ground
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Power switch pushed → Power switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch2
    I3-7 (SSW1) - Body ground
    Input
    R - Body ground
    SSW1 contact signal
    Power switch pushed → Power switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch1
    I4-2 (IG1D) - Body ground
    Output
    P - Body ground
    IG1 signal
    20°C (68°F)
    40.74 to 59.49 Ω
    IG1 Relay Monitor(Outside)
    I4-1 ACCD) - Body ground
    Output
    W - Body ground
    ACC signal
    20°C (68°F)
    81.49 to 118.98 Ω
    ACC Relay Monitor
    I3-14 (SPDI) - I3-6 (E1)
    Input
    V - BR
    Vehicle speed signal
    Always
    30 kΩ or higher
    Vehicle Speed Signal
    I3-15 (P2) - I3-6 (E1)
    Input
    R - BR
    P position signal
    Always
    40 kΩ or higher → 200 Ω or less
    Shift P Signal

  3. Reconnect the A39, I3 and I4 connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    A39-2 (IG2D) - I3-6 (E1)
    Output
    R - BR
    IG2 signal
    Power switch on (ACC) → Power switch on (IG)
    1 V or less → 9 V or higher
    IG2 Relay Monitor(Outside)
    I4-16 (SLP) - I3-6 (E1)
    Input
    P - BR
    Steering lock position signal
    Steering wheel locked → Steering wheel unlocked*1
    11 to 14 V → 1.2 V or less
    Steering Unlock Switch
    I4-6 (SLR+) - I3-6 (E1)
    Output
    SB - BR
    Steering lock motor operation command signal (Steering lock motor operation permission signal sent from the power management control ECU)
    Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*2
    Pulse generation (See waveform 1)
    -
    I3-15 (P2) - I3-6 (E1)
    Input
    R - BR
    P position signal
    Shift lever in P → Shift lever not in P
    9 V or higher → 1.5 V or less
    Shift P Signal
    I4-17 (SSW2) - I3-6 (E1)
    Input
    V - BR
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Power switch not pushed → Power switch pushed
    9 V or higher → 1 V or less
    Start Switch2
    I3-7 (SSW1) - I3-6 (E1)
    Input
    R - BR
    SSW1 contact signal
    Power switch not pushed → Power switch pushed
    9 V or higher → 1 V or less
    Start Switch1
    I4-1 (ACCD) - I3-6 (E1)
    Output
    W - BR
    ACC signal
    Power switch off → Power switch on (ACC)
    1 V or less → 8.5 V or higher
    ACC Relay Monitor
    I4-2 (IG1D) - I3-6 (E1)
    Output
    P - BR
    IG1 signal
    Power switch on (ACC) → Power switch on (IG)
    1 V or less → 9 V or higher
    IG1 Relay Monitor(Outside)
    I3-14 (SPDI) - I3-6 (E1)
    Input
    V - BR
    Vehicle speed signal
    Vehicle being driven at approx. 5 km/h (3 mph)
    Pulse generation
    (See waveform 2)
    Vehicle Speed Signal

    HINT:
    1. *1: When the power switch is turned off with the shift lever in P and any of the doors are opened or closed, the steering wheel will be locked. When the power switch is turned on (ACC) or on (IG), the steering wheel will be unlocked.
    2. *2: When all of the following conditions are met, open any of the doors to operate the steering lock motor.
      1. The shift lever is in P.
      2. The power switch is off.
      3. While carrying the electrical key transmitter sub-assembly, the power switch is turned on (IG) and the steering is unlocked.



  5. Using an oscilloscope, check the waveform of the ECU.



      C221561E01
    1. Waveform 1
      Item
      Content
      Tester Connection
      I4-6 (SLR+) - I3-6 (E1)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Vehicle Condition
      Steering lock motor stopped →
      Steering lock motor operating →
      Steering lock motor stopped
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating

      HINT:
      When all of the following conditions are met, open any of the doors to operate the steering lock motor.
      1. The shift lever is in P.
      2. While carrying the electrical key transmitter sub-assembly, the power switch is turned on (IG) and the steering is unlocked.
      3. The power switch is off.



    2. B220145E01
    3. Waveform 2
      Item
      Content
      Tester Connection
      I3-14 (SPDI) - I3-6 (E1)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Vehicle Condition
      Power switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.